manualshive.com logo in svg

Shel lab BACTRON300, Installation And Operation Manual, Page: 82 / 86

Share
Download
Shel lab BACTRON300 Installation And Operation Manual Download Page 82

 

82 | 

P a g e

 

 

ACCESSORIES (CONTINUED) 

 

Compressed Gas Cylinder Switcher, Automatic 

Allows two gas cylinders to be connected to one gas 
port, and automatically switches from the first to the 
second cylinder when the first is empty. 

Part Number 2002-B (110 - 120 Volts)

 

 

BACTRON300 and BACTRON600 \ BACTRON900 
Microscope Adaptors 

Designed for the Lecia S6 Spotting Stereo 
Microscope. 

BACTRON300: Part Number 9990535

 

 

BACTRON600 and BACTRON900: 

Part Number 9990511 

 

BACTRON300 Stand 

A rolling stand with cabinet for the BACTRON300. 

29.3 inches high by 61.5 inches wide 

(74cm high by 156cm wide) 

Part Number 9000511 

 

BACTRON600/900 Stand 

A rolling stand with two (2) cabinets for the 
BACTRON600 and 900. 

88.5 inches wide, 30 inches depth, 29 inches high  

(225cm wide, 76.2cm depth, 74 cm high) 

Part Number 9000512 

Summary of Contents for BACTRON300























































































Reviews:

No comments