Sharp XE-A404 Page 79 Instruction Manual Download | Manualshive

Page: 79 / 132

background image

77

Caution: The paper cutter is mounted on the printer (receipt side). Be careful not to cut yourself. Never

touch the print head immediately after printing, because the head may still be hot.

1.

Remove the printer cover.

2.

Pull the print head release lever all the way forward (after it stops at one
position, continue pulling forward until it stops again and cannot be pulled
forward any further).

3.

Remove the paper jam. Check for and remove any shreds of paper that may
remain in the printer.

4.

Return the print head release lever to its original position.

5.

Reset the paper roll correctly by following the steps in “Installing the paper
roll”.

6.

Replace the printer cover.

When the printed text is getting dark or faint, paper dust may be stuck to the print head. Clean the print head as
follows:

Caution:
• Never touch the print head with a tool or anything hard as it may damage the head.
• The paper cutter is mounted on the printer (receipt side). Be careful not to cut yourself.

1.

Turn the mode switch to the OFF position.

2.

Remove the printer cover.

3.

Pull the print head release lever all the way forward (after it stops at one
position, continue pulling forward until it stops again and cannot be pulled
forward any further).

4.

Clean the print head with a cotton swab or soft rag moistened with ethyl
alcohol or isopropyl alcohol.

5.

Return the print head release lever to its original position immediately after
cleaning.

6.

Reset the paper roll correctly by following the steps in “Installing the paper
roll”.

7.

Replace the printer cover.

Cleaning the Print Head

6

Removing a Paper Jam

5

Print head

A404_6 OPERATOR MAINTENANCE 06.6.20 3:26 PM Page 77

«
...
77
78
79
80
81
...
»

Summary of Contents for XE-A404





































































































































Reviews:

No comments

Related manuals for XE-A404

Brand: Tektronix Pages: 133

Brand: Seneca Pages: 4

Brand: DR. JOHANNES HEIDENHAIN Pages: 29

Brand: Logia Pages: 10

Brand: Olympia Pages: 16

Brand: Olympia Pages: 60

E5-648-C446 Series

Brand: Eaton Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands