Sharp XE-A404 Page 42 Instruction Manual Download

Page: 42 / 132

The cash register provides miscellaneous keys such as

(when using as RA key),

(when using as PO key),

(when using as CONV key),

and

(when using as CA

key). While the cash register is pre-programmed so you can use these keys, you must set a currency
conversion rate to use

key. You can also program these keys for more convenient use. Please refer to

the data below for programming these keys. Factory setting is indicated with parentheses.

Percent rate (0.00%), tax status (non-taxable), sign (minus), item % and subtotal %
entry* (both are allowed), percent rate limitation (100%)

Amount (0.00), tax status (non-taxable), sign (minus), item

and subtotal

entry*

(both are allowed), entry digit limit (7 digits)

Not necessary to program

Entry digit limit (9 digits)

Currency conversion rate (0.0000), currency conversion rate entry method - open or
preset (both are enabled)

and

Compulsory entry of amount tender (not compulsory), entry digit limit (8 digits), footer
printing (not printed)

(Manual tax)

Entry digit limit (7 digits)

* Item %/Item

Percent/discount calculation is applied to individual department and PLU/UPC.

* Subtotal %/Subtotal

: Percent/discount calculation is applied to subtotals.

Rate for

and

(when using as CONV key)

*: Rate

0.00 — 100.00 (% rate)
0.0000 — 9999.9999 (Currency conversion rate)

You must use a decimal point when setting fractional rates.

Percent rate

Currency

conversion rate

8063

Print

Key operation example

*Rate

%
K

To program another rate

To program zero

Miscellaneous Key Programming

A404_3 FOR THE MANAGER 06.6.20 3:25 PM Page 40

Summary of Contents for XE-A404





































































































































Search results

Summary of Contents for XE-A404

Reviews:

Related manuals for XE-A404

Brands by name

Popular brands

Sharp XE-A404, Instruction Manual

Search results

Summary of Contents for XE-A404

Reviews:

Related manuals for XE-A404

Brands by name

Popular brands