Sharp XE-A177 Full Detailed Instruction Manual Download Page 79

Page: 79 / 134

■

Foreign currency (Exchange1, Exchange2)

Procedure

Program each item as follows:

The screen continues.

• PRESET RATE (Use the selective entry)

ENABLE: Enables preset rate

DISABLE: Disable preset rate

• RATE (Use the numeric entry)

Currency exchange rate (0.000000 to 999.999999)

• TEXT (Use the character entry)

Description for the currency exchange key. Up to 12

characters can be entered.

• SYMBOL (Use the character entry)

Currency descriptor. Up to 4 characters can be entered.

• TAB (Use the selective entry)

Tabulation (0 to 3)

• OPEN RATE (Use the selective entry)

ENABLE: Enables open rate

DISABLE: Disable open rate

• TEXT (Use the character entry) for open rate

Description for the currency exchange key for open rate. Up to
12 characters can be entered.

• SYMBOL (Use the character entry) for open rate

Currency descriptor for open rate. Up to 4 characters can be
entered.

• TAB (Use the selective entry) for open rate

Tabulation for open rate (0 to 3)

NOTE

Currency symbol is printed with (+) amount of foreign currency.
The programmed character is printed at left side of amount.

EX) Case of “DM”:

EXCH1

1.234567

DM 1.23

Programmed symbol

Summary of Contents for XE-A177







































































































































Search results

Summary of Contents for XE-A177

Reviews:

Related manuals for XE-A177

Brands by name

Popular brands

Sharp XE-A177, Full Detailed Instruction Manual

Search results

Summary of Contents for XE-A177

Reviews:

Related manuals for XE-A177

Brands by name

Popular brands