Sharp UX-B800A, Service Manual, Page: 52 / 140

UX-B800A
2 – 38
SW22 No. 1 Activate Receive Fax to E-mail
The Receive Fax to E-mail function ON/OFF is set.
SW22 No. 2 Print setting of received fax for Receive Fax to E-mail
This soft switch is used to select before.
0: Received FAX is always printed when Receive Fax to E-mail func-
tion worked.
1: Received FAX is printed only transfer error when Receive Fax to E-
mail function worked.
SW22 No. 3 Report setting for Receive Fax to E-mail
This soft switch is used to select before.
0: Transfer result is always printed when Receive Fax to E-mail func-
tion worked.
1: Transfer result is printed only transfer error when Receive Fax to E-
mail function worked.
SW22 No. 4 Activate Secure Receive
The Secure receive function ON/OFF is set.
SW22 No. 5 ~ No. 8 Reserved
SW23 No. 1 Ink save mode
If set to "1", printing is done with half of ink.
SW23 No. 2 Receive reduce setting
If set to 1, it is reduced automatically when receiving.
SW23 No. 3, No. 4 Paper size
The paper size is set.
SW23 No. 5 Half tone copy print swath direction
The direction of the half tone copy printing is set.
SW23 No. 6 ~ No. 8 Reserved
SW24 ~ SW31 No. 1 ~ No. 8 Reserved
SW32 No. 1 ~ No. 3 Reserved
SW32 No. 4 Error criterion
Used to select error criterion for sending back RTN when receiving
image data.
SW32 No. 5, No. 6 EOL (End of Line) detection timer
Used to make a choice of whether to use the 25-second or 13-second
timer for detection of End of line This is effective to override communi-
cation failures with some facsimile models that have longer End of line
detection.
SW32 No. 7, No. 8 Reserved
SW33 ~ SW38 No. 1 ~ No. 8 Reserved
SW39 No. 1 ~ No. 6 Reserved
SW39 No. 7 Make/Break ratio in D.P.
Used to set pulse ratio of D.P. mode.
SW39 No.8 Pre pause time in D.P.
This setting is used for the pause time before dial pulse start.
SW40 No. 1 ~ No. 3 Inter digit pause time
Used to set the pause time between pulse.
SW40 No. 4 Change to PB from PB by “ “ key.
When setting to 1, the mode is changed by pressing the key from the
pulse dial mode to the tone dial mode.
SW40 No. 5 ~ No. 8 Reserved
SW41 No. 1, No. 2 DTMF detect time
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5
). The longer the detection time is, the error
detection is caused by noises.
SW41 No. 3 Protection of remote reception (5 ) detect
Used to set the function of remote reception (5 ). When set to “1”,
the remote reception function is disabled.
SW41 No. 4 ~ No. 7 Remote operation code figure by external
TEL(0-9)
Remote operation codes can be changed from 0 through 9. If set to
greater than 9, it defaults to 9. The “5” is not changed.
SW41 No. 8 Reserved
SW42 ~ SW50 No. 1 ~ No. 8 Reserved
SW51 No. 1 ~ No. 5 Reserved
SW51 No. 6 Busy tone detect when TEL/FAX mode
This setting is used to enable or disable busy tone detection in the
TEL/FAX mode.
SW51 No. 7 Dial tone detect when TEL/FAX mode
This setting is used to enable or disable dial tone detection in the TEL/
FAX mode.
SW51 No. 8 Reserved
SW52 ~ SW60 No. 1 ~ No. 8 Reserved
SW61 No. 1, No. 2 Reserved
Ringer volume:
The calling sound volume of CI signal receiving is set.
SW61 No. 3, No. 4 Ringer volume
This allows selection of MTF correction (dimness correction) in the half
tone mode.
When "NO" (=1) is selected, the whole image becomes soft and mild.
Clearness of characters will be reduced. Normally set to "YES" (=0).
SW61 No. 5, No. 6 Speaker volume
The line monitor volume is set.
SW61 No. 7, No. 8 Reserved
SW62 ~ SW109 No. 1 ~ No. 8 Reserved
SW110 No. 1 ~ No. 3 Connect configuration for LAN controller
Used to the communication speed when connecting to LAN.