background image

R-22GT-F
R-22GV-F

In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens con-
tain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Recti-
fier Assembly,  High Voltage Harness etc..)

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICE TO
AVOID POSSIBLE  EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONEL .................................................................................................................. 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD .......................................................................................................................................................... 3
PRODUCT SPECIFICATIONS .............................................................................................................................. 4
GENERAL  INFORMATION ................................................................................................................................... 4
OPERATION .......................................................................................................................................................... 6
TROUBLE SHOOTING GUIDE/ TEST PROCEDURE ........................................................................................ 10
TOUCH CONTROL PANEL ................................................................................................................................. 20
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE ................................................................ 30
PICTORIAL DIAGRAM ........................................................................................................................................ 37
CONTROL PANEL CIRCUIT ............................................................................................................................... 38
PRINTED WIRING BOARD ................................................................................................................................. 39
PARTS LIST ........................................................................................................................................................ 40
PACKING AND ACCESSORIES ......................................................................................................................... 43

S8509R22GTF//

R-22GT-F
R-22GV-F

COMMERCIAL

MICROWAVE OVEN

MODELS

 SERVICE MANUAL

SHARP CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

1200W/R-22GT

DOUBLE

QUANTITY

EXPRESS

DEFROST

1

11

2

12

3

13

4

14

5

15

6

16

7

17

8

18

9

19

0

20

SET

CHECK

SIGNAL

STOP/CLEAR

SELECTAPOWER

START

SELECTATIME

R-22GT-F

Summary of Contents for R-22GT-F

















































Reviews: