background image

15

R - 2 0 9 F K
R - 2 0 9 F W

In the interest of user-safety the oven should be restored to its original
condition and only parts identical to those specified should be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens con-
tain circuitry capable of producing very high voltage and
current, contact with following parts may result in a severe,
possibly fatal, electrical shock. (High Voltage Capacitor, High
Voltage Power Transformer, Magnetron, High Voltage Recti-
fier Assembly,  High Voltage Harness etc..)

S2204R209FPW/

R - 2 0 9 F K
R-209FW

MICROWAVE OVEN

MODELS

SHARP CORPORATION

This document has been published to be used for after
sales service only.
The contents are subject to change without notice.

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE  EXPOSURE TO EXCESSIVE MICROWAVE ENERGY ................... INSIDE FRONT COVER
BEFORE SERVICING ...................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL ................................................................................................................ 1
MICROWAVE MEASUREMENT PROCEDURE ................................................................................................... 2
FOREWORD AND WARNING ............................................................................................................................... 3
PRODUCT DESCRIPTION .................................................................................................................................... 4
OPERATION .......................................................................................................................................................... 4
OVEN SCHEMATIC ............................................................................................................................................... 5
TEST PROCEDURE .............................................................................................................................................. 6
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE .................................................................. 7
PICTORIAL DIAGRAM .......................................................................................................................................... 8
CONTROL PANEL CIRCUIT ................................................................................................................................. 9
PARTS LIST ........................................................................................................................................................ 10
PACKING AND ACCESSORIES ......................................................................................................................... 13

This is a supplemental Service Manual for Models R-209FK and R-209FW. These models are
quite similar to base model R-220EW. Use this supplemental manual together with the Base
Model Service Manual (Refer No. is S1101R220EPW/) for complete operation, service informa-
tion, etc..

SUPPLEMENTAL SERVICE MANUAL

;

;

;

;

;;

;

;

;;

;;

;

;;

;

;

;

;

;

;;

;;

;;

;;

;;

;

;

;

DEF.

LBS.

QTY. CHECK

ON

Summary of Contents for R-209FK

















Reviews: