Sharp LC-19LE320, Service Manual, Page: 76 / 367

LC-19LE320, LC-22LE320, LC-26LE320, LC-32LE320, LC-37LE320, LC-42LE320
76
<External input AV1(Component)>No picture on the display (10)
↓
Does not the picture of the component video signal input to Component go out?
TERMINAL_UNIT:
↓
MAIN_UNIT:
↓ YES
↓ YES
< During external connection > No picture on the monitor (1)
↓
No picture appears on SCART1 - connected monitor during the tuner (U/V) reception.
↓
TERMINAL_UNIT:
↓
↓ NO
↓ NO
< During external connection > No picture on the monitor (2)
AVOUT:
↓
No picture from SCART1 appears on AVOUT-connected monitor.
NOTE: Normally, if the screen during display is sent to SCART1, no picture is sent to AVOUT.
↓
TERMINAL_UNIT:
↓
↓ NO
↓ NO
Is Component Y/Pb/Pr signal sent to pin (2)/Y, (4)/Pb, (6)/Pr of
AV1(CN111) ?
NO
Check the setting of an external input device that connects of
CN111.
Refer to “ The picture doesn't appear in all modes. ”
Is Component Y/Pb/Pr signal sent to pin (AU26)/Y, (AT27)/Pb,
(AP27)/Pr of IC U401?
NO
Check the line between IC U401 and CN111.
Is CVBS signal output into pin (19) of CN151 (SCART1)?
YES
Check the setting of an external input device that connects of
CN151.
Refer to “ The picture doesn't appear in all modes. ”
Is U401 pin (AT31) CVBS signal output into pin (19) of CN151
(SCART1)?
YES
Check the line between CN151 and U401.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device? … Set it to “ CVBS ” , “ Y/C ” , “ RGB ” , “ AUTO ” .
2) Is ANT-CABLE disconnected or connected improperly? … Connect it correctly as per the operation manual.
3) The picture is sent to the monitor in a CVBS signal if the source during display is ATV/DTV, CVBS or Y/C of SCART1, AV3.
When sent by component, etc., that signal is not sent to the monitor.
4) When the monitor picture is not sent and is not displayed on the monitor, refer to “ No picture ” for each terminal.
5) The video output from SCART1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to SCART1. (Specification)
Is CVBS signal output into pin (2) of CN140?
YES
Check the setting of an external input device that connects of
CN140.
Refer to
“
The picture doesn't appear in all modes.
”
Is CVBS signal output from pin (AP31) of IC U401 into pin (2) of
CN140 ?
YES
Check the line between CN140 and IC U401.
Checklist:
1) Is the Signal Type (item) in MENU-Option-Input Select equal to Signal Type of an external device?
…
Set it to
“
CVBS
”
,
“
Y/C
”
,
“
AUTO
”
.
2) The picture is sent to the monitor in a CVBS signal if the source during display is TV, CVBS or Y/C of SCART1, AV3.
When sent by component, etc., that signal is not sent to the monitor.
3) When the monitor picture is not sent and is not displayed on the monitor, refer to “ No picture ” for each terminal.
4) The video output from SCART1 is not the monitor output (output of the picture now watching).
The picture of the last selected TV channel is always sent to SCART1. (Specification)