background image

EC-HX100M_P

6

7

EMPTYING THE DUST CUP

(Red: ON)

When the Filter care lamp (red) 

turns ON*

• 

Parts that can be washed with water

When dirt collects to “Dust Full” line

• 

When operation stops 

• 

When suction force is weak 

• 

When operation sound changes or 

becomes louder 

• 

Remove the dust cup assembly, turn the filter knob, 

and empty the contents.(See right.)

If the lamp is still ON, the filter must be cleaned. 

Even if the dirt is collected on one side, empty the dust cup 

before the dirt exceeds the line.

For sanitary purposes, the dust cup should be emptied  

after each cleaning session.

If operation is continued with a full dust cup, the dirt will 

adhere onto the mesh filter, and cause the suction force 

to drop.

• 

Notice

If operation is continued without cleaning, the cleaner 

will stop automatically. Even if cleaning is required, 

the Filter care lamp may not turn ON depending 

on the room temperature and operation state, etc.

Clean the unit frequently.

• 

Do not use thinners, benzene or hot water

(approx. 40°C or hotter).

• 

Notice

Dust cup ejector lever

Knob

Cover portion

Dust disposal hook

(yellow)

Dust disposal

hook

(yellow)

Yellow mark

Hook

Indent

7-9

Page

Turn the filter knob approx.

ten times.

Click

Click

Tap the dirt on the pleat filter 

into the dust cup.

• 

Dust cup assembly

MAINTENANCE

Always follow the attaching procedure, and correctly set the dust cup assembly into the cleaner. 

Failure to do so could cause the suction force to drop, abnormal sounds to be heard, or dirt could enter 

the motor and cause faults. 

• 

Wipe the cleaner with a soft cloth, etc. 

so the cleaner and floor are not scratched.

• 

Support the cleaner with a hand so that it 

stays stable.

• 

When removing and cleaning the dust cup 

assembly, clean the dust cup assembly 

storage section first.

• 

The dust cup assembly must be assembled to be properly mounted onto the cleaner.

• 

Do not lose the mesh filter (lower) when emptying the dust cup or cleaning the cleaner.

• 

The dust cup will not fit onto the cleaner body if there is dirt in the dust cup storage section.

• 

Cautions

Dust cup

Hook

Guide for emptying the dust cup

(Red: quick flicker)

When the Filter care lamp (red) 

flickers quickly*

• 

When cleaner body is hot

• 

When fine powders have been sucked up

• 

When Filter care lamp (red) turns ON 

frequently

• 

Wash the dust cup and filter with water when the following states apply.

Guide for cleaning

Removing the Dust Cup

Emptying the dust cup

Mounting the Dust Cup

Mesh filter

“Dust Full” line

Always disconnect the power plug 

before starting servicing or inspections.

(There is a risk of electric shocks or injury.)

WARNING 

EC-HX100M_P.indd   6

15/09/25   16:40

Summary of Contents for EC-HX100M-S







Reviews: