EC-HX100M_P
8
5
Start of
operation
Air is warming up
Turns OFF if operation is
stopped within 30 minutes
of starting
Approx. 1 minute
before auto stop
Auto stop
(Turns OFF approximately
30 minutes after starting)
Lightly move the cleaner slowly back and forth as shown in the illustration.
(Do not press down on the cleaner.)
•
Clean one section back and forth two times to attain a cleaner state.
•
At the start of operation, if the cleaner is set on the mattress rather
than lifted up, the hot air will circulate and warm up the air faster.
•
Do not store the cleaner into
the storage stand while it is running.
•
Do not place the stand at an unstable place,
such as a high pile carpet.
[ The stand could fall over. ]
•
Do not carry the cleaner around while
it is stored in the storage stand. [ The cleaner
could fall out of the storage stand and drop,
causing injuries, damage the floor,
or breaking. ]
Do not pull the storage stand.
[ It could damage the floor, etc. ]
•
•
If there is a space between the mattress and cleaner body, the hot air
will cause fine dust to scatter and possible stick onto the cleaner body.
Cleaner body maintenance
•
11
Page
Hints for Cleaning Mattress
Storing the Cleaner
Storage stand
Cord storage section
Cord band
During cleaning, the Warming lamp will turn ON as shown below to indicate the operation state.
Warming lamp (Orange)
Warming lamp (orange) lighting state
Lamp state
Slow flicker
Operation state
Warming air with maximum power.
Dust can be vacuumed even if the air temperature is low.
Steady light
Fast flicker
OFF
Flicker 3 times
Air is starting to warm up.
The cleaner’s effect against mites increases with hot air.
The time required to reach a hot air level may vary according to
the room’s temperature.
If the motor temperature (air temperature) is at the maximum
level, the power will not change even if ”
” is
pressed. The lamp will flicker quickly three times.
When operating with the maximum power for heating the air,
if the power is lowered by pressing “
”, the lamp
will remain OFF until the air heats up.
(The lamp will automatically change to a steady light
when the hot air level is reached.)
The operation will automatically stop approx. one minute
after the lamp starts to flicker quickly, and the Warming lamp
will turn OFF.
To continue operation even after automatic stop, press
“
” again to resume operation.
For safety purposes, operation will automatically stop approx.
30 minutes after starting. The Warming lamp will flicker quickly
approx. one minute before automatic stop.
Steady light
Fast flicker
* If hot air is discharged as soon as
operation starts, the lamp will
change to a steady light.
(Ex. When starting operation
soon after the previous operation.)
Slow flicker
*
Slowly move
back and forth
Cautions
20～30cm
Store the power plug outside of the storage
section with the plug facing upward
Do not pinch power cord
or fingers.
[
There is a risk of power
cord damage or injury. ]
①
Knob
Wash with water or a diluted neutral detergent.
Cover portion
Filter cover
Pleat filter
Mesh filter
(top)
Mesh filter
Filter ejector
button (red)
Dust disposal hook
(yellow)
②
Dust cup
Mesh filter
(bottom)
Pleat filter
Mesh filters (top and bottom) /
Filter cover and dust cup
Wash the back side thoroughly.
If there are heavy odors or contamination,
soak the filter in a solution of 10ml
clothing-safe
bleach and 1 liter of water for approx. 3 hours.
Then, wash well with water.
•
Turn the filter knob approx.
ten times.
Tap the dirt on the pleat filter
into the dust cup.
•
Removing the Filters
Washing the Filters
①
③
④
⑤
⑥
•
Shake off as much water as possible, and then gently wipe with towels to remove excess water.
Leave the filters to dry in a well-ventilated shady place.
[
Failure to dry the filters properly will cause odors or faults. ]
•
Do not dry the filters with hot air, such as with a dryer.
[ There is a risk of deformation or faults. ]
Guide to drying time: 12 hours (This varies by the environment and seasons.)
After washing with water
MAINTENANCE
(Continued)
Always disconnect the power plug
before starting servicing or inspections.
(There is a risk of electric shocks or injury.)
WARNING
EC-HX100M_P.indd 5
15/09/25 16:40
