background image

INSTALLATION MANUAL

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT:  SAVE  THIS  INSTALLATION  MANUAL  FOR  LOCAL  ELECTRICAL 
INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CLEARANCES & DIMENSIONS

For SAFETY CONSIDERATIONS do not install a appliance in any combustible cabinetry which is not 

in accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.

APPLIANCE MEASUREMENTS .................................2

CLEARANCES AND DIMENSIONS ..............................2

IMPORTANT NOTES .............................................3

UNPACKING AND EXAMINING YOUR APPLIANCE ...........3

IMPORTANT SAFETY INSTRUCTIONS .........................3

INSTALLATION, ANTI-TIP ................................... 4-6

CHECKING INSTALLATION ......................................6

ELECTRICAL CONNECTIONS ...................................6

POWER CONNECTIONS .........................................7

MODEL AND SERIAL NUMBER LOCATION ....................8

CARE, CLEANING AND MAINTENANCE  ......................8

BEFORE YOU CALL FOR SERVICE  ............................8

E

LECTRIC

 C

OOKT

OP

+M

ICROW

AVE

 D

RA

WER

SPECIAL WARNING

Summary of Contents for Cooktop









Reviews: