manualshive.com logo in svg

Sharp AR-PB2A, Service Manual, Page: 30 / 40

Share
Download
Sharp AR-PB2A Service Manual Download Page 30

(Error message)

F9

0

Content

ICU-PRT communication trouble

Detail

Cause 

SCSI LSI abnormality
ICU PWB defect
SCSI connector connection defect
Printer PWB defect

Check and remedy

Replace the printer PWB.
Check the SCSI connector.
Replace the  printer PWB.
Replace the ICU PWB.

F9

01

Content

PRT DRAM trouble

Detail

DRAM trouble in the option printer board. (When operating the scanner mode)

Cause

DRAM module is broken and access cannot be made. 
DRAm module installation trouble

Check and remedy

Check with SIM 57-1. 

F9

02

Content

PRT Centro port check error

Detail

Option printer board Centro port trouble

Cause

Centro port defect
Printer PWB defect

Check and remedy

Replace the printer board.

F9

03

Content

Network card trouble.

Detail

Network card self test trouble.

Cause

Network card defecft.
Printer PWB defect.
Network card connector connection defect.

Check and remedy

Check the Network card connector.
Replace the printer PWB.
Replace the Network card.

F9

04

Content

Printer program error.

Detail

Program data trouble in the option printer board.

Cause

Flash memory data is destroied.

Check and remedy

Replace or rewrite the Flash memory.
Replace the printer PWB.

F9

05

Content

Short of memory capacity on the ICU PWB

Detail

Total memory is less than 16MB on the ICU PWB.

Cause

Memory defect
SIMM memory connector connection defect
ICU PWB defect
Wrong type SIMM memory is installed

Check and remedy

Replace the ICU PWB
Replace the memory
Check the memory connector

F9

10

Content

PRT SCSI LSI abnormality

Detail

An error occurred in SCSI communication with the option printer board.

Cause

SCSI LSI abnormality
ICU PWB defect
Printer PWB defect
SCSI connector connection defect

Check and remedy

Replace the printer PWB.
Check the SCSI connector. 
Replace the printer PWB. 
Replace the ICU PWB. 

F9

90

Content

ICU-PRT communication trouble (PRT detection)

Detail

Cause

SCSI LSI abnormality
ICU PWB defect
SCSI connector connection defect
Printer PWB defect

Check and remedy

Replace the printer PWB. 
Check the SCSI connector.
Replace the printer PWB. 
Replace the ICU PWB. 

AR-PB2A

Summary of Contents for AR-PB2A









































Reviews:

No comments