Sharp AR-M550N Service Manual Download Page 357

Page: 357 / 460

AR-M550/M620/M700 SELF DIAG MESSAGE AND TROUBLESHOOTING 9 - 2

5. Breakdown sequence

A. Breakdown mode process

(1) Breakdown mode list

There are following cases of the breakdown mode.

∗

For FAX communication, refer to the sheet of “Call request and Call-
in.”

∗

The machine may be operated under some conditions.

∆

1: When detected except when in a job, the machine can be operated

in the OC mode.

∆

2: Can be operated except in the staple mode.

∆

3: When detected except in a job, the machine can be operated

except with the breakdown tray.

∆

4: Can be operated with some restriction on the image quality

depending on the destination. (Low density print) * Refer to the
process control trouble operation table below.

∆

5: When detected except in a job, can be operated except in the trou-

ble paper exit section.

∆

6: When detected except in a job, can be operated in the single sur-

face scan mode.

∆

7: Can be operated except in the inserter tray, if the error is detected

in the standby mode.

∗

Process control trouble operation table

Judgment

block

Trouble code

Operation enable mode

(The machine can be operated under
some conditions.)

Copy read

(including

interrupt)

FAX

send

receive

FAX
print

List

Notification

FASThost

(SPF breakdown)

Scanner

∆

❍

Scanner section breakdowns (Mirror
motor, lens, copy lamp)

Scanner

L1, L3, U2 (80, 81)

❍

FAX board breakdown

MFP control/

FAX

F6, F7

❍

FAX power OFF

MFP control

❍

Network error

MFP control CE

❍

Staple breakdown

PCU

F1 (10)

∆

❍

∆

❍

Paper feed tray breakdown

PCU

F3, U6 (LCC)

∆

❍

∆

❍

(Process control breakdown)

PCU

F2 (31, 32, 37)

∆

❍

∆

❍

PCU section breakdowns (Motor, fusing
section, etc.)

PCU

C1, C2, C3, H2, H3, H4,
H5, L4 (excluding L4-30),
L8, U2 (90, 91), F2, F4

❍

After-process breakdown

PCU

∆

❍

∆

❍

Inserter trouble (excluding
communication trouble)

PCU

F1 (61, 62)

∆

❍

∆

❍

Laser breakdown

PCU

E7 (02 only), L6

❍

HDD breakdown

MFP control E7 (03)

❍

CCD breakdowns (Shading, etc.)

Scanner

E7 (10, 11, 12, 14)

❍

CIS breakdowns (Shading, etc.)

Scanner

E6 (10, 11, 14)

∆

❍

Scanner communication trouble

MFP control E7 (80)

❍

PCU communication trouble

MFP control E7 (90)

❍

FAX backup battery voltage fall

MFP control U1 (01, 02)

❍

HDD registration data sum error

MFP control U2 (50)

❍

Thermistor trouble (trouble history)

PCU

F2 (39, 46, 47, 48)

❍

(The machine cannot be operated.)

Memory

MFP control U2 (00, 11, 12, 22, 23)

❍

External communication disable (RICA)

MFP control U7, PF

❍

Image memory trouble, decode error

MFP control E7 (01, 06)

❍

Incompatibility check error

MFP control/

PCU

E7 (50, 55, 56, 57, 60,
65, 66, 67)

Controller fan motor trouble

MFP control L4-30

Trouble

code

Error content

Japan/SEC

Europe/

Others

F2-31

Process control sensor
gain adjustment failure

Machine stop

Low density
copy

F2-32

Mark detection failure

Low density
copy

F2-37

Mark sensor gain
adjustment failure

Machine stop

Low density
copy

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Search results

Summary of Contents for AR-M550N

Reviews:

Sharp AR-M550N, Service Manual, Page: 357 / 460

Search results

Summary of Contents for AR-M550N

Reviews: