manualshive.com logo in svg

Sharp AR-M550N, Service Manual, Page: 18 / 460

Share
Download
Sharp AR-M550N Service Manual Download Page 18

: Feb. 9 2004

1

AR-M550/M620/M700  SPECIFICATIONS  3 - 9

(7)

Copy functions

C. Image send function

(1) Mode

Scanner (Scan to E-mail, Scan to Sharp desk, Scan to FTP, Scan to
HDD ), FAX, Internet FAX

(2) Support system

(3) Support image

(4) Image process

(5) Address specification

(6) Multiple address specification

*: Direct address input: 10-key other than one-touch, and soft keyboard

input

• When broadcast includes FAX, the resolution is set to the FAX reso-

lution.

• The compression system in broadcast conforms to the key operator

setup.

Automatic paper selection

❍

Automatic magnification ratio 
selection

❍

Vertical/horizontal 
independent magnification 
ratio

❍

Paper type selection

❍

 By type setup

Auto tray switching

❍

Rotation copy

❍

Electronic sort

❍

Rotation sort

❍

Job reservation

❍

Tray installation priority

×

Program call/register

❍

Document filing

❍

Preheat function

❍

 Set by the key operator

Auto power shut off function

❍

 Set by the key operator program

Dept. management

❍

 500 department

Process control

❍

Tandem copy

❍

 (Via network)

Indefinite document size input

❍

Indefinite paper size input

❍

Binding margin

❍

Edge erase/Center erase

❍

1 set 2 copy

❍

Cover/Insert paper/Tab insert 
paper

❍

OHP insert paper

❍

Tab copy

❍

Centering

×

Multi shot (N in 1)

❍

 (2 in 1/4 in 1) (Centering provided)

Card shot

❍

Center binding

❍

 (Centering provided)

Duplex copy system switch

❍

Large volume document mode

❍

 (Max. 10000 sheets)

Black-white reversion

❍

Shading

×

Mirror image

❍

Enlargement continuous copy ×
Repeat

×

Date print

×

Stamp

×

Page print

×

Mode

Scanner

Internet FAX

FAX

Supported 
server

SMTP server

FTP server

POP server

SMTP server

ESMTP server

–

Mode

TIFF, PDF, TIFF-F, TIFF-FX

Compression 
system

Scanner

Internet FAX

FAX

Non-compression

G3 (1st dimension) 

= MH (Modified 

Huffman)

G4 = MMR 

(Modified MR)

MH, MMR

MH, MR, 

MMR, JBIG

Mode

Scanner

Internet FAX

FAX

half tone 
reproduction

Equivalent to 256 gradations

Density 
adjustment

Auto + 5 steps

Image quality 
selection

Half tone ON/OFF (*: Not available)

Resolution 
(Differs 
depending on 
the file type/
communication 
system.)

200×200dpi *

200×100dpi *

Normal text 

(203.2×97.8dpi)*

300×300dpi

200×200dpi

Small text 

(203.2×195.6dpi)

400×400dpi

200×400dpi

Fine text 

(203.2×391dpi)

600×600dpi

400×400dpi

Ultra fine text 

(406.4×391dpi)

–

600×600dpi

–

Mode

Scanner

Internet FAX

FAX

LDAP

❍

 (Can be registered as one-touch address.)

Address 
specification

Specified by one-touch, group, or direct address 

input.

No. of one-
touch 
registration 
items

Max. total 999 items

(of which 200 can be assigned to FTP and/or 

desktop)

Group

❍

 Registered from the one-touch dial and the direct 

dial. (Max. 500 items)

Program

❍

 (8 items)

Direct address 
input

Soft keyboard

Input by the 10-

key, # key, and * 

key.

Chain dial 
(Direct address 
input)

–

Used together 

with Pause. Up to 

64 digits.

Resend

The previous address is called.

Reduction 
address 
selection

The address registration number is called by the 10-

key input.

Mode

Scanner

Internet FAX

FAX

Address 
specification

Specified by one-touch, group, or direct address 

input *.

No. of 
registration 
items of direct 
address input *

Max. total 5000 items of group/interface broadcast

Broadcast send

❍

 (Broadcast 

send is disabled 

for FTP/

Desktop)

❍

Sequential send 
request

–

❍

1

Summary of Contents for AR-M550N













































































































































































































































































































































































































































































Reviews:

No comments