Sharp AR-C260 Operation Manual Download Page 89 | Manualshive

Page: 89 / 140

background image

REDUCTION/ENLARGEMENT/ZOOM

5-13

5

Manual selection

Manual selections can be made in the range of 25% to 400%.
There are four preset reduction ratios (25%, 50%, 64% and 77%) and four preset enlargement ratios (121%, 129%,
200% and 400%) available for the inch system. There are six preset reduction ratios (25%, 50%, 64%, 70%, 81% and
86%) and five preset enlargement ratios (115%, 122%, 141%, 200% and 400%) available for the AB system.

<The key operator program on page 13 of the key operator's guide can be used to set two additional enlargement
ratios and two additional reduction ratios.>

1

Place the original in the document feeder
tray (when a reversing automatic
document feeder is installed) or on the
document glass. (page 4-6)

2

Touch the [COPY RATIO] key.

3

Use the [MENU] key to select menu "

" or

menu "

" for copy ratio selection.

Menu

●

A. Preset reduction copy ratios are:

77% and 64% (for the inch system).
70%, 81% and 86% (for the AB system).

●

B. Preset enlargement copy ratios are:

121% and 129% (for the inch system).
115%, 122% and 141% (for the AB system).

Menu

●

A. Preset reduction copy ratios are:

50% and 25%.

●

B. Preset enlargement copy ratios are:

200% and 400%.

(The custom ratios set by the key operator appear
in ratio menu 2.)

4

Use the reduction, enlargement, and
[ZOOM] keys on the touch panel to set the
desired copy ratio.

Zoom ratios: Any ratio
from 45% to 400% can
be set in 1% increments.
Touch the [

] key to

increase the ratio, or the
[

] key to decrease

the ratio. If you continue
to touch either key for 3
seconds, the ratio
begins to change
quickly.

5

Touch the [OK] key.

AUTO 8½x11

PAPER SELECT

100

%

COPY RATIO

READY TO COPY.

100

ZOOM

%

77

%

64

%

121

%

129

%

XY ZOOM

MENU

AUTO IMAGE

2

1

0

OK

100

%

EXPOSURE

PAPER SELECT

COPY RATIO

AUTO

AUTO 8½x11

11x17
8½x14
11x17
8½x11

8½x14
8½x11
8½x11
5½x8½

8½x14 11x17

8½x11 11x17
5½x8½ 8½x11

READY TO COPY.

0

100

ZOOM

OK

%

50

%

200

%

25

%

400

%

100

%

XY ZOOM

MENU

AUTO IMAGE

2

1

EXPOSURE

PAPER SELECT

COPY RATIO

AUTO

AUTO 8½x11

NOTES

●

Touch a reduction or enlargement key to set the
approximate ratio, then touch the [

] key to

decrease the ratio or the [

] key to increase the

ratio.

●

The message "IMAGE IS LARGER THAN COPY
PAPER." may appear, indicating that the selected
copy ratio is too large for the copy paper size.
However, if you press the [START] key, a copy will
be made.

●

To set the horizontal and vertical copy ratios
separately, use the XY ZOOM feature. See page
5-15.

100

ZOOM

%

77

%

64

%

121

%

129

%

XY ZOOM

MENU

2

1

11x17
8½x14
11x17
8½x11

8½x14
8½x11
8½x11
5½x8½

8½x14 11x17

8½x11 11x17
5½x8½ 8½x11

100

ZOOM

%

77

%

64

%

121

%

129

%

XY ZOOM

MENU

AUTO

2

1

8½x14
8½x11
8½x11
5½x8½

8½x14 11x17

8½x11 11x17
5½x8½ 8½x11

77

ZOOM

%

121

%

129

%

NU

AUTO IMAGE

OK

100

%

PA

C

AU

4 11x17

1 11x17
½ 8½x11

00-08.book 13

ページ

２００２年１１月８日　金曜日　午前９時３９分

«
...
87
88
89
90
91
...
»

Summary of Contents for AR-C260













































































































































Reviews:

No comments

Related manuals for AR-C260

imagePROGRAF iPF8400

Brand: Canon Pages: 157

Brand: Canon Pages: 91

Brand: Panasonic Pages: 3

Brand: Panasonic Pages: 4

Brand: Magicard Pages: 30

Brand: Magicard Pages: 35

MAGICARD ID Card Printer

Brand: Magicard Pages: 30

Brand: Magicard Pages: 6

Brand: Datamax Pages: 19

imageRUNNER 2545i

Brand: Canon Pages: 37

Brand: Panasonic Pages: 486

Brand: Oki Pages: 140

Brand: AGFA Pages: 266

Brand: Aficio Pages: 156

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: Telpar Pages: 25

SignJet JS310 Series

Brand: GRAPHTEC Pages: 83

Brand: Oki Pages: 132

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands