Sharp AR-BC320 Operation Manual Download Page 86 | Manualshive

Page: 86 / 140

Sharp AR-BC320 Operation Manual Download Page 86

NORMAL COPYING

5-8

4

Select the desired output mode. (See page
5-5.)

When a document is
detected on the
document glass, the
group mode will be
automatically selected.
To select sort copy,
touch the [OUTPUT]
key, then touch the

[SORT] key on the displayed screen, and then
touch the [OK] key.

5

Use the numeric keys to set the desired
number of copies.

Up to 999 can be set.
If you are only making a
single copy, the copy
can be made with the
copy number display
showing "0".
Use the [C] (clear) key to
cancel an entry if a
mistake has been made.

6

Press the [COLOR COPY START (

)]

or [BLACK COPY START (

)] key.

Replace the original with
the next original and
press the [START] key.
Repeat this operation
until all originals have
been scanned.

7

Touch the [READ-END] key.

If you selected "Sort" for
the output in step 4, it is
necessary to touch the
[READ-END] key.

NOTE

If the [SORT] or [GROUP] key is touched, its
corresponding icon will appear on the touch panel.
To clear the icon display, press the [CA] (clear all)
key. Note that all selections made to that point will be
canceled.

2-SIDED COPY

OUTPUT

READ-END

PLACE NEXT ORIGINAL. PRESS [START].

WHEN FINISHED, PRESS [READ-END].

WhaleII_general-copy_SEC.book 8

ページ

２００４年９月１４日　火曜日　午前１１時４５分

«
...
84
85
86
87
88
...
»

Summary of Contents for AR-BC320













































































































































Reviews:

No comments