manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 87 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 87

NORMAL COPYING

5-9

5

Automatic two-sided copying from the document glass

When a duplex module/2 x 500 sheet paper drawer and a duplex bypass/inverter unit are installed, the following
automatic two-sided copy function is possible. The copy paper is turned over automatically, allowing easy two-sided
copying.

1

Place an original on the document glass.
(pages 4-6 to 4-9)

2

Touch the [2-SIDED COPY] key.

3

Touch the [1-sided to 2-sided copy] key.

When making automatic two-sided copies of a
one-sided 11" x 17" (A3) or 8-1/2" x 14" (B4) size
portrait original, or when the front and back side of
a two-sided original are copied backwards, touch
the [BINDING CHANGE] key.

4

Touch the [OK] key.

Make selections and proceed as in steps 3 to 7 on
pages 5-7 and 5-8.

NOTE

Certain restrictions exist depending on the amount of memory installed and the copy settings. (See "Copy mode
output restrictions" and "Guidelines for the number of scannable originals during sort copying" on page 5-4.)

Original

Copy

2-SIDED COPY

OUTPUT

Example of a 
portrait-oriented 
original

Example of a 
landscape-oriented 
original

BINDING

CHANGE

OK

ApollonII_general-copy_SEC.book  9 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments