Home
/
Sharp
/
AR-BC260
/
Operation Manual

Sharp AR-BC260, Operation Manual, Page: 127 / 184

Share

Page: 127 / 184

Sharp AR-BC260 Operation Manual Download Page 127

7-3

7

USER MAINTENANCE (For copying)

To ensure good service from this product over a long period of time, it is recommended that the following
maintenance procedures be performed on a regular basis.

Wipe with a clean, soft cloth.
If necessary, moisten the cloth with water or a small amount of neutral detergent.
When finished, wipe dry with a clean cloth.

If you find that a dirty image results when a copies are made using the reversing single
pass feeder, wipe the original scanning area (the area that contains the long narrow
glass shown at left).

CLEANING THE ORIGINAL SCANNING AREA

If you find that black (or white) lines appear when you make copies using the reversing single pass feeder, use the
accessory glass cleaning tool to clean the original scanning area.

1

Open the reversing single pass feeder and
remove the glass cleaning tool.

2

Clean the original scanning area with the
glass cleaning tool.

3

Replace the glass cleaning tool in its
storage position.

CAUTION

Do not use flammable spray to clean the machine. If gas from the spray comes in contact with hot electrical
components or the fusing unit inside the machine, fire or electrical shock may result.

NOTE

When cleaning, do not use thinner, benzene, or similar volatile cleaning agents. These may

degrade or discolor the housing.

Example of dirty print image

Black lines

Original feed direction

White lines

ApollonII_general-copy_SEC.book 3

ページ

２００４年９月６日　月曜日　午後４時５７分

«
...
125
126
127
128
129
...
»

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments