manualshive.com logo in svg

Sharp AR-BC260, Operation Manual, Page: 107 / 184

Share
Download
Sharp AR-BC260 Operation Manual Download Page 107

6-11

6

COLOR ADJUSTMENTS MENU

The [COLOR ADJUSTMENTS] menu in [SPECIAL MODES] enables the following parameters to be adjusted to
modify the characteristics of a color copy.
Settings adjusted with the color adjustments menu do not affect black and white copying.

RGB ADJUST (next page 6-12)

Strengthens or weakens one of three primary
colors, R (red), G (green), or B (blue).

SHARPNESS (page 6-13)

Sharpens or softens image outlines.

SUPPRESS BACKGROUND (page 6-13)

Suppresses copying of lighter background areas.

COLOR BALANCE (page 6-14)

Adjusts the color, tone, and density of color copies.

BRIGHTNESS (page 6-15)

This copier allows the level of brightness to be
adjusted. If brightness is selected, color tone can
be darkened or lightened.

INTENSITY (page 6-15)

This copier allows the level of intensity to be
adjusted. If intensity is selected, color saturation
can be made to be more vivid or more dull.

SPECIAL MODES

MARGIN SHIFT

ERASE

COVERS

TRANSPARENCY

INSERTS

CENTERING

OK

DUAL PAGE 
COPY

SPECIAL MODES

IMAGE EDIT

COLOR

ADJUSTMENTS

B/W
REVERSE

OK

2

 

Touch the [COLOR ADJUSTMENTS] key in 

the second SPECIAL MODES screen.

COLOR 

ADJUSTMENTS

RGB ADJUST

SHARPNESS

SUPPRESS 

BACKGROUND

BRIGHTNESS

INTENSITY

OK

1

 

Touch the       key to switch to the 

second SPECIAL MODES screen.

COLOR

BALANCE

ApollonII_general-copy_SEC.book  11 

ページ

  

２００４年９月６日　月曜日　午後４時５７分

Summary of Contents for AR-BC260

























































































































































































Reviews:

No comments