manualshive.com logo in svg

Sharp AR-7024, Operation Manual, Page: 105 / 141

Share
Download
Sharp AR-7024 Operation Manual Download Page 105

105

TROUBLESHOOTING

7

Paper misfeed.

Misfeed occurs.

To remove the misfeed, see "MISFEED REMOVAL".

114

The paper is outside of the specified size and weight 
range.

Use copy paper within the specified range.

38

Paper curled or damp.

Do not use curled or crimped paper. Replace with dry copy paper. 
During periods when the machine is not used for a long time, 
remove the paper from the tray and store it in a dark place in a 
bag to prevent moisture absorption.

–

Paper is not loaded properly.

Make sure the paper is properly installed.

39

Pieces of paper inside machine.

Remove all pieces of misfed paper.

114

Too much paper is loaded in the tray.

If the stack of paper is higher than the indicator line on the tray, 
remove some of the paper and reload so that the stack does not 
exceed the line.

39

The guides on the bypass tray do not match the width of 
the paper.

Adjust the guides to match the width of the paper.

40

The bypass tray extension is not pulled out.

When loading a large size of paper, pull out the extension.

40

The bypass paper feed roller is dirty.

Clean the roller.

125

Original size not selected 
automatically.

 (When the 

RSPF

 is installed.)

Original(s) curled.

The original size cannot be correctly detected if the original is 
curled or folded. Straighten the original.

–

The machine is directly exposed to sunlight.

Install in a location that is not exposed to sunlight.

–

Copies are smudged or dirty.

The document glass or the underside of the document 
cover/RSPF is dirty.

Clean regularly.

124

Original smudged or blotchy.

Use a clean original.

–

White or black lines appear on 
copies.

The scanner glass for the RSPF is dirty.

Clean the long, narrow scanning glass.

124

Paper size for a paper tray cannot 
be set.

Copying or printing is performed.

Set the paper size after copying or printing is complete.

–

The machine has stopped temporarily due to running out 
of paper or a misfeed.

Load paper or remove the misfeed, and then set the paper size.

39, 114

An interrupt copy job is in progress.

Set the paper size after the interrupt copy job is finished.

57

The number of copies display is blinking.

Data is being held in memory. Print the data in memory or clear it 
from memory.

60, 62

Problem

Cause and solution

Page

Summary of Contents for AR-7024














































































































































Reviews:

No comments