manualshive.com logo in svg

Sharp AR-317 Operation, Key Operator'S Manual

Share
Download
Sharp AR-317 Operation Key Operator'S Manual Download Page 204

3

PRINTER UTILITIES (WINDOWS)

28

C O N T E N T S

Printer utilities

The "Software" CD-ROM contains the following two printer 
utilities.

Printer Status Monitor (for general users)

This allows the user to check on the computer screen whether 
or not the machine is able to print.
It provides information on error states such as paper misfeeds 
and shows the configuration of the machine (number of trays, 
whether or not there is a finisher, etc.) by means of illustrations. 
Available paper sizes and paper remaining are also indicated.

Printer Administration Utility (for administrators)

This allows the administrator to check information on supplies 
and error states of the machine and other SHARP printers 
(compatible with the Printer Administration Utility) that are 
connected to the network. Settings can also be changed via the 
utility.

Before using the Printer Status Monitor

Note the following points before using the Printer Status 
Monitor.

Printing via a server

When the first print job is executed after starting up the Printer 
Status Monitor, the machine's IP address is automatically set in 
the Printer Status Monitor.

Direct printing without a server

Install and configure the software as explained in "USING THE 
MACHINE AS A NETWORK PRINTER" in the software setup 
guide for network printer. (This is not necessary if the software 
has already been installed and configured.)

To install the Printer Status Monitor and Printer 
Administration Utility, see software setup guide for 
network printer.

Note

Summary of Contents for AR-317 Operation















































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands