USING YOUR REMOVABLE HANDHELD STEAMER
7
To remove the Handheld Steamer, press and hold down the Handheld Release Buttons
while pulling out the Handheld Steamer. (
fig. 7
)
fig. 8
QUICK START GUIDE
Simple steps to get you cleaning
and sanitising with your new
Shark
®
LIFT-AWAY
™
Pro
Steam
®
Mop S3901*.
GETTING
STARTED
Pro Steam Pocket
®
Mop
P R O F E SS I O NA L
PROBLEM
POSSIBLE REASONS & SOLUTIONS
fig. 1
*For more detailed information please refer to your owner’s guide.
1
Insert the Mop Handle into the Steam Mop Housing. Make sure it is inserted past the
line printed on the pole. Secure the assembled handle and pole by inserting the large
screw through the exposed hole and tightening with a phillips or a flat head screw
driver. (
fig. 1
)
2
Slide the mop head into the cleaning
pad pocket. Secure the quick fasteners
on the top of the pocket. (
fig. 2
)
STEAM MOP ASSEMBLY
3
Push the mop head into the mop body
until you hear it snap into place. (
fig. 3
)
4
Turn the water tank cap counter clockwise and remove from the tank. Use the filling flask
to pour water into the tank. Do not overfill. Replace the cap on the water tank. (
fig. 4
)
NOTE
: Sweep or vacuum your floors prior to cleaning with your Steam Mop.
We recommend using distilled water to prolong the life of your Shark
®
Steam Pocket
®
Mop.
fig. 2
fig. 3
fig. 4
USING YOUR STEAM MOP
5
Unwrap the power cord completely and plug into an electrical outlet.
The STEAM CONTROL button LED will flash blue.
6
Press the STEAM CONTROL button to select your steam setting. Press the button once
for
LO
mode, twice for
MED
mode and three times for
HI
mode. Clean your floors with a
forward and backward motion. See the Owner’s Guide for additional information on each
setting and specific usage requirements. (
fig. 5, 6
)
NOTE
: The Carpet Glider can be used to lightly steam your carpets.
(
fig. 6
)
fig. 6
fig. 7
LO
- Light steam for quick dusting and best dry time.
MED
- Normal, every day steam cleaning.
HI
- Heavy cleaning and will leave floors damp.
ATTACHING AND REMOVING CLEANING TOOLS
8
Attach your desired cleaning tool by pressing the nozzle of the tool onto the Handheld
Steamer until it clicks into place. (
fig. 8
)
9
When being used as a Handheld Steamer the STEAM CONTROL light will always be solid
blue. Press and hold the steam trigger to create steam. The steam mode setting can be
changed by pressing the STEAM CONTROL button. The setting can be changed while
steaming or when the Handheld Steamer is at rest.
10
To remove the cleaning tool, press and hold down the Handheld Release Buttons then
slide the cleaning tool off the Handheld Steamer using the grips on the tool.
NOTE:
Reference your Owner’s Guide for more information and detailed instructions
on using your cleaning tools.
CAUTION
: Do not press the steam trigger until the Cleaning Tool is snapped into the
main nozzle of your Handheld Steamer
fig. 5
Your steam mop should be securely plugged into an electrical outlet only. Check your fuse or breaker.
Is there water in the water tank? If not, add water to your steam mop following instructions on page 5 of your owners guide.
If the unit still does not make steam, follow the decalcification instructions in your owner’s guide.
If you have already plugged in your unit, unplug and try a different outlet. This may reset the standby mode.
Add water to the tank and press the STEAM CONTROL button to select a steam setting.
Check to see if your cleaning pad is soaked through. If so, we recommend you unplug the steam mop
and change the cleaning pad. Make sure the cleaning pad is attached correctly.
Do not leave your steam mop on the floor with a damp or wet cleaning pad. If you are using tap water,
we recommend switching to distilled water. Make sure the water tank door is closed securely.
Make sure the cleaning pad is attached correctly.
Check to see if the cleaning pad is excessively dirty. Replace if the cleaning pad is too dirty or wet.
The
Lift-Away
™
Pro
Steam Pocket
®
Mop S3901
will not turn-on.
The unit will not
make steam.
Cannot activate steam
flashing blue light remains on.
The
Lift-Away
™
Pro
Steam Pocket
®
Mop S3901
leaves water on the floor.
The
Lift-Away
™
Pro
Steam Pocket
®
Mop S3901
left a white spot on the floor.
Floors are cloudy, streaky
or spotty after steaming.
The
Lift-Away
™
Pro
Steam Pocket
®
Mop S3901
is hard to push.
• The pad might be dirty, change the pad.
• If you washed the cleaning pad with powder detergent, your pad may be damaged and needs replacement.
• You might have left the mop in the same spot for too long.
• Do you have hard water? If you do, we recommend you switch to distilled water.
• This might be leftover residue. Use the steam mop a few more times and see if the leftover cloudiness is removed.
If this does not work, we suggest rinsing the floor with water, letting it dry, and then steam mopping again with a
clean pad. One or more rinses generally removes the residue. A more stubborn case may require you to rinse the
floor with a mixture of one part vinegar and two parts water.
11
When finished using your steam mop, press the STEAM CONTROL button until the light
returns to flashing blue. Unplug the mop and allow it to cool for 2-3 minutes before storing.
12
When finished using your Handheld Steamer, release the steam trigger.
The STEAM CONTROL button LED will remain solid blue.
Unplug the Handheld Steamer and allow it to cool for 2-3 minutes before removing
the cleaning tools and storing.
S3901UK
S3901UK_QSG_150619
Paper: Quality A (Bright White) 157g/m2
Coating: Matte both sides
OR
First attach the Accessory Hose by pressing the Nozzle
base onto the Handheld Steamer until it clicks into place.
Slide the All-Purpose Scrubbing Pad over the Flat
Scrubber Tool. DO NOT use the Flat Scrubber Tool
without the All-Purpose Scrubbing Pad attached.
Press the Flat Scrubber Tool onto the Accessory
Hose until it clicks into place.
DIRECT STEAM NOZZLE
For spot cleaning and direct steaming
FLAT SCRUBBER TOOL
Cleaning countertops, appliances and
other above floor surfaces
CUSTOM CLEANING TOOL
HOW TO ATTACH
Your Handheld Steamer can be used to clean, sanitise and freshen many of your
above floor surfaces. Follow the quick steps below to get started.
SQUEEGEE TOOL
Cleaning windows and glass surfaces
GROUT SCRUBBER TOOL
Removing stubborn messes in hard-to-reach
nooks, corners and in grout
Slide Nozzle base directly onto the Handheld Steamer.
Attach the Window Squeegee by snapping into the handle
of the Accessory Hose.
Select either LO, MED or HI mode by pressing the ON/STEAM
SETTING button and wait until the selected setting indicator
light turns solid blue. Hold down the
steam trigger to start steaming.
Attach the Grout Scrubber by snapping into the handle
of the Accessory Hose.
Select either LO, MED or HI mode by pressing the ON/STEAM
SETTING button and wait until the selected setting indicator
light turns solid blue. Hold down the steam trigger to start
steaming.
S3901
