Shanghai High-Flying Electronics Technology Co. HF-LPT120 User Manual Download

Page: 50 / 65

High-Flying

HF-LPT120 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 50 -



Yes: Disable power save



mode:



No: Enable power save



Yes: Disable power save

4.2.2.56.

AT+NTPRF



Function: Set /Query time calibration interval



Format:



Query Operation

AT+NTPRF<CR>
+ok=<num><CR><LF><CR><LF>



Set Operation

AT+NTPRF=<num><CR>
+ok<CR><LF><CR><LF>



Parameters:



num

：

time calibration inverval

，

range:0~720, default:30 minutes, 10 minutes for

each step, set 0 means no time calibration automatically.

4.2.2.57.

AT+NTPEN



Function: Enable/Disable time calibration function. Setting is valid after reset.



Format:



Query Operation

AT+NTPEN<CR>
+ok=<status><CR><LF><CR><LF>



Set Operation

AT+NTPEN=<status><CR>
+ok<CR><LF><CR><LF>



Parameters:



status

：

status of time calibration



：

Enable time calibration



off

：

Disable time calibration

4.2.2.58.

AT+NTPTM



Function: Query network time,time zone is GMT+8 by default.



Format:



Query Operation

AT+NTPTM<CR>
+ok=<time><CR><LF><CR><LF>



Parameters:



time

：

networ time, for example: 2013-10-9 16:10:42 Wed

，

if it shows Not

Available means that the time calibration function is not enabled or the module
doesn’t connect to the internet.

4.2.2.59.

AT+NTPSER



Function: Set/Query NTP server IP address..

Summary of Contents for HF-LPT120


































































Search results

Summary of Contents for HF-LPT120

Reviews:

Related manuals for HF-LPT120

Brands by name

Popular brands

Shanghai High-Flying Electronics Technology Co. HF-LPT120, User Manual

Search results

Summary of Contents for HF-LPT120

Reviews:

Related manuals for HF-LPT120

Brands by name

Popular brands