Shanghai High-Flying Electronics Technology Co. HF-LPT120 User Manual Download

Page: 11 / 65

High-Flying

HF-LPT120 Low Power WiFi Module User Manual

Shanghai High-Flying Electronics Technology Co., Ltd(www.hi-flying.com)

- 11 -

1.2.

Hardware Introduction

1.2.1.

Pins Definition

Figure 1.

HF-LPT120 Pins Map

Table 2 HF-LPT120 Pins Definition

Pin

Description

Net Name

Signal

Type

Comments

Ground

GND

Power

+3.3V Power

DVDD

Power

3.3V@300mA

Restore

Configuration

nReload

I/O,PU

Can be configured as GPIO_2

Detailed functions see <Notes>

Module Reset EXT_RESETn

I,PU

―Low‖ effective reset input.

UART0

UART0_RX

GPIO_19

UART0

UART0_TX

O,PU

GPIO_20

GPIO_5

I/O

Can be configured as UART0_RTS,

UART1_TXD,GPIO_5

GPI_6

GPIO_6

I/O

Can be configured as UART0_CTS,

UART1_RXD,GPIO_6

GPIO_3

nReady

I/O

Can be configured as nReady,GPIO

GPIO_15

nLink

I/O

Can be configured as nLink,GPIO

Detailed functions see <Notes>

I—Input, O—Output,PU—Internal Pullup Resistor

；

I/O: Digital I/O

；

Power—Power

<Notes>

nReload Pin (Button) function

：

When this pin is set to “low” during module boot up, the module will enter wireless
firmware and config upgrade mode. This mode is used for customer manufacture.

Summary of Contents for HF-LPT120


































































Search results

Summary of Contents for HF-LPT120

Reviews:

Related manuals for HF-LPT120

Brands by name

Popular brands

Shanghai High-Flying Electronics Technology Co. HF-LPT120, User Manual

Search results

Summary of Contents for HF-LPT120

Reviews:

Related manuals for HF-LPT120

Brands by name

Popular brands