Thank you for choosing a Shakespeare product. Shakespeare
works hard to build reliability and durability into all of its products
for maximum customer satisfaction. Customer comments are
welcome. Before installing, please study the diagram and check
parts supplied against those listed.
Supplied parts:
(1) SRA-50 Antenna with 6” cable and TNC Female connector
(1) 25’ Coax Cable with TNC Male and SMB connectors
The length of the cable run from the antenna to the satellite radio receiver can be extended by
using the one of the cable kits listed on page 6 (each sold separately).
Note:
These cables
replace the 25’ cable supplied with the antenna, and must be used as supplied. They cannot
be lengthened, shortened, or connected together as extensions.
(1) Bag containing: (1) Extension shaft, (1) Lockwasher, (1) Retaining nut
(1) Antenna Base for low profile mounting
(1) Base Gasket
(1) Pedestal Top for mounting on standard 1”-14 mounts
(1) Rubber Seal Ring
(1) Pedestal Bottom for pedestal mounting
Tools required:
Screwdriver, Marking pencil, drill and drill bits (9/16”, 7/64”), needle nose pliers,
or other tools appropriate to your specific application may also be needed.
Required materials:
Silicone Sealer (RTV) when flush mounting
DO NOT CUT OR ALTER THE ANTENNA CABLE.
DO NOT REMOVE ITS CONNECTOR.
IMPORTANT: Please read all instructions before installing.
Optional Accessories
SRS-3-Kit
DC Voltage Splitter for antenna cables up to 50’
The length of the cable run from the antenna to the satellite radio receiver can be extended by using the
one of the optional cable kits listed above. Note: These cables
replace
the 25’ cable supplied with the
antenna, and must be used as supplied. They cannot be lengthened, shortened, or connected together as
extensions.
1
Satellite Shooter Template
Trace the triangle below on a sheet of paper, then cut out the triangle and use as a
template on thick paper or poster-board.
1. Tape this edge to paper tube or straight edge.
2. Sight through tube or top of straight edge for clear
view of sky.
This corner should be next to the mounting
hole when scanning.
This edge must be kept horizontal at the mounting location
EXTENSION MAST OR RAIL MOUNTING
If you are attaching the antenna to a marine extension mast or rail mount:
Step 1:
Route the 6” cable from the antenna through the Pedestal Top.
Step 2:
Screw the antenna onto the Pedestal Top.
Step 3:
Route the 25’ (or optional) cable through the extension mast or rail mount.
Step 4:
Attach the 25’ cable’s connector to the connector on the 6” antenna cable.
Step 1:
Step 5:
Screw the antenna assembly onto the extension mast or rail mount.
IMPORTANT:
Rotate the cable counterclockwise while turning the antenna assembly clockwise. Make sure
the cable turns freely and does not bind.
SPECIAL NOTE: The hole in ratchet-type antenna mounts will not accommodate the
SRA-50’s connector. You must use the included flange mount, a rail mount, or an extension mast,
which will allow the cable and its connector to pass through.
Do not cut the cable and do not
remove the connector.
Skip to “Completing the installation,” below.
The Shakespeare Galaxy® Style SRA-50 Satellite Radio Antenna is
a versatile antenna for receiving SiriusXM® Satellite Radio. The antenna’s
versatile mounting permits attaching the antenna directly to a flat surface,
on a low profile base, to the included Pedestal Mount kit, to an optional
extension mast (1”-14 thread), or to a Shakespeare Style 4720 Rail Mount
(sold separately). When the pedestal base is used, the kit allows routing the
antenna’s coax cabling with or without passing the cable through the
mounting surface. In all cases, a SiriusXM Vehicle Tuner and Subscription
are required.
(1) Pedestal Gasket
This instruction sheet
Style SRA-50
5
If a low-profile mounting option is desirable and access under the mounting surface is
unavailable,
the antenna can be mounted onto the low-profile Antenna Base which can then be
screw in from the top. The cable with its connector attached can be routed through a 9/16” hole
drilled in the mounting surface, or passed through the knife slit on the Base Gasket.
If you are running the cable through the mounting surface:
If you are running the cable through the mounting surface:
Follow Steps 2 through 4 above.
LOW PROFILE BASE MOUNTING
Step 2:
Attach the antenna onto the Antenna Base by using the nut and washer.
Step 3:
Step 4:
Drill a 9/16” center hole for the antenna cable. When drilling fiberglass surfaces,
use a small backup block of scrap wood to control push-through splintering. Use caution to
avoid drilling through or near fuel lines, fuel tanks, hydraulic lines, or electrical wiring.
Orient the antenna as required, place on the mounting surface and take off the antenna
leaving the gasket in the same position. Use gasket as a stencil to mark locations for mounting
holes.
Step 6:
Use the supplied self-tapping screws or other stainless steel hardware (not supplied) to
mount the antenna assembly onto the surface. Do not overtighten.
Step 5a:
Pass the 6” cable along with the connector through the center hole and place the
Antenna with Antenna base and Base Gasket onto the mounting surface aligning it to the
marks made in Step 4.
Step 5b:
Lay the 6” cable into the Knife-slit and place the Antenna with Antenna base and
Base Gasket onto the mounting surface aligning it to the marks made in Step 4 in the above
section. Go back and complete previous section from Step 6.
The supplied mounting screws will accommodate most surfaces. If you find them too
long, too short, or otherwise unsuitable for your application, substitute wood screws, machine
screws/washers/nuts, or other hardware (not supplied). Be sure to use only stainless steel
hardware. If you find it too difficult to start the screws, drill 7/64” pilot holes.
Completing the installation
Step 1:
Route the cable to your satellite radio receiver.
IMPORTANT: If your satellite receiver has two antenna input terminals, the optional SRS-1
Splitter may be required. Newer models may differ, so consult your dealer or Shakespeare for up-
to-date information.
Step 2:
Attach the SMB connector to your satellite radio receiver. See the receiver’s manual
for precautions and instructions. Done!
SRC-35
35’ RG-58 cable kit with connectors
SRC-50
50’ RG-58 cable kit with connectors
SRC-90
90’ RG-8X cable kit with connectors
