SF
50
H
50m
1.6m
SF
150
H
150m
2.6m
SF
250
H
250m
4.4m
1
1
2
2
4
4
5
5
7
7
6
6
8
8
3
3
TAMPER
TAMPER
COM NO NC
ALARM
4-
φ
4
.
5
13
1
1
1
2
1
2
2
2
2
2
3
3
3
4
4
4
1
1
13
11
11
11
11
4*60mm
4*60mm
POWER
DC/AC10v-24v
20mA max
◆
◆
◆
POWER
DC/AC10v-24v
70mA max
Quad Photoelectric Beam Detector User Manual
Thanks for purchasing quad photoelectric beam detector, please read the user manual carefully
before installation.
WARNING
CAUTION
Do not use the product for purposes other than the detection of moving objects such as people and
vehicles. Do not use the product to activate a shutter, etc.which may cause an accident.
Never attempt to disassemble or repair the product. It may cause fire or damage to the devices.
Do not exceed the voltage or current rating specified for any of the terminals during installation,
doing so may cause damage to the devices.
Do not touch the unit base or power terminals of the product with a wet hand ( do not touch when the
product is wet with rain etc.) It may cause electric shock.
Do not pour water over the product with a bucket, hose, etc. The water may enter which may cause
damage to the devices.
Clean and check the product periodically for safe use. If any problem is found, do not attempt to use
the product as it is and have the product repaired by a professional engineer or electrician.
1. Features
Interruption time adjustable
NO / NC relay outputs
Integrated tamper switch, turns on when cover is moved.
Frequencies selectable for long distance and stacking installation
LED display signal grade for easy alignment
Wide voltage and energy-saving design
“And” “Or” technology
Digital communication function
FRESNEL lens
IP65 Waterproof grade: IP65
Alignment angle horizontally
±
90
°
, vertically
±
10
°
Digital filtering, high environment adaptability to eliminate false alarms
Anti-beam interference, workable in harsh situations.
2.Part Description
Front Cover
Front Cover
Base
Body
Lock Screw
U Bracket
Mounting Plate Holes
Cover Lock Nut
Wire Hole
Fresnel Lens
Up-bracket
Horizontal adjust
Terminals
Vertical adjust scale
Vertical Alignment
Screw
Horizontal Alignment
Bolster
3. Installation notes
1.Please avoid below situations to assure performance
1.Do not install on the unsteady
or not soiled surface
2.Do not install the unit where objects
can block the beams like the plants
and laundry can be moved by wind.
3.Prevent direct sunlight or fluorescent
object entering into internal receiver.
4.Avoid any other detector interference
(stack installation only for same model)
5.Avoid aerial wiring
2.Normal installation
Detection distance
Mounting height
Model
Detection Distance
Beam Angle
Beam spread range
Beam spread range
Detection
Angle
Mounting height 0.7~1.0m
Detection Distance
Adjusting Angle
Horizontal 180
°（±
90
°）
Vertical 20
°
(
±
10
°）
Notice:
For best testing results,
please avoid testing in 45
°
4. Setting method
1.Wall mounting
1.Loosen the screw and remove the cove
2. Attach the installation paper to the wall,mark
the holes first and then make the guide holes.
3.Wiring hole: Remove the foam plug,pull
wire through.and reset the foam plug.
Wiring Knockout
4.Drop into the four holes with the
expansion pipes,fix them with screws.
5.Connecting wires to the terminals
(please refer to “beam alignment”)
6.Review and reset the cover
2.Pole mounting
Bracket diameter
1. Break out the wire hole and pull out
the wires.
2. Remove the cover
3. Drop into the holes with the expansion
pipe,fix it with screws
Wiring Knockout
Wiring Pressing
U type bracket
4.Fix the body on the bracket
5. Back to back installation diagram,others
please refer to the step 5 and 6 of the wall
mounting method.
5. Connectors
Warning
when installation , don't connect the port with the voltage or current which is
over the normal specification!
Transmitter
Receiver
Notes:
1 . Power voltage input: DC/AC 10V-24V.
2 . No heater in the package, please order if required.
3 . The tamper switch is independent of other circuit;
it would open if the cover was removed
Notes:
1 . Power voltage input: DC/AC 10V-24V.
2 . No heater in the package, please order if required.
3 . The tamper switch is independent of other circuit;
it would open if the cover was removed.
4 . Relay connection point 1C 24VDC 0.5Amx
6.Connecting wires
1.Single connect: Control panel operating
voltage DC12V. NC alarm output.
Connecting to power supply parallel
Alarm input
Alarm input
Control panel
Control panel
Transmitter
Transmitter
Receiver
Receiver
2.Stacked connect. Control panel operating
voltage DC12V.NC alarm output series
connect
plate
scale
SF50H
SF150H
SF250H
