manualshive.com logo in svg

SEW-Eurodrive MOVIFIT-FC, Operating Instructions Manual, Page: 71 / 172

Share
Download
SEW-Eurodrive MOVIFIT-FC Operating Instructions Manual Download Page 71

5

Electrical Installation

Hybrid ABOX "MTA...-S62.-...-00"

Operating Instructions – MOVIFIT

®

-FC

71

5.7.2

Variants 

The following variants of the hybrid ABOX are available for MOVIFIT

®

-FC (MTF):

• MTA11A-503-S6

2

.-...-00: 

– Optional external braking resistor
– Optional integrated braking resistor
– Optional switch disconnector

The following figure shows the screw connections and plug connectors of the hybrid
ABOX:

5.7.3

Pin assignment of fieldbus interface (X11/X12)

934776075

M25

M16

M20

M12, standard coding, female

M12, standard coding, female

M20

M16

Push-Pull
RJ45

PROFINET
EtherNet/IP
Modbus/TCP   

MTA11A-503-S

6

.

3

-...-00

MTA11A-503-S

6

.

3

-...-00

MTA11A-503-S

6

.

3

-...-00

Ethernet (PROFINET, EtherNet/IP, or Modbus/TCP)

X11 (Port1)

Pin

Assignment

X12 (Port2)

Pin

Assignment

Push-pull RJ45 plug 

connector

1

TX+

Push-pull RJ45 plug 

connector

1

TX+

2

TX–

2

TX–

3

RX+

3

RX+

4

Res.

4

Res.

5

Res.

5

Res.

6

RX–

6

RX–

7

Res.

7

Res.

8

Res.

8

Res.

NOTICE

According to IEC PAS 61076-3-117, push-pull RJ45 sockets may only be used with the
appropriate push-pull RJ45 mating connector. Commercially available RJ45 patch
cables without push-pull connector housings do not lock into the connectors. Such
cables can damage the sockets and are, therefore, not suitable.

8

6

5

4

3

1

2

7

8

6

5

4

3

1

2

7

Summary of Contents for MOVIFIT-FC













































































































































































Reviews:

No comments