SEW-Eurodrive MOVIFIT-FC Operating Instructions Manual Download Page 21

Page: 21 / 172

Mechanical Installation

Assembly instructions

Operating Instructions – MOVIFIT

-FC

4.3

Assembly instructions

1. Drill the holes necessary to secure at least four screws to the mounting surface as

shown in the following figure. SEW-EURODRIVE recommends using screw size M6
and, depending on the base, suitable dowel pins, if necessary.

Size 1
In conjunction with a standard mounting rail:

758540299

334.5

303.5

280

140

37,9

min. 40

min. 50

[1]

[2]

TIPS

• [1] Observe the minimum installation clearance so that the EBOX can be removed

from the ABOX.

• [2] Observe the minimum installation clearance required to operate the mainte-

nance switch and to ensure heat dissipation for the unit.

For detailed dimension drawings, see the section "Dimension drawings" (see page 146).

Summary of Contents for MOVIFIT-FC













































































































































































Search results

Summary of Contents for MOVIFIT-FC

Reviews:

SEW-Eurodrive MOVIFIT-FC, Operating Instructions Manual, Page: 21 / 172

Search results

Summary of Contents for MOVIFIT-FC

Reviews: