manualshive.com logo in svg

SEW-Eurodrive MOVIFIT-FC, Operating Instructions Manual, Page: 135 / 172

Share
Download
SEW-Eurodrive MOVIFIT-FC Operating Instructions Manual Download Page 135

9

Technical Data

Interfaces

Operating Instructions – MOVIFIT

®

-FC

135

9.8

Interfaces

9.8.1

PROFIBUS interface

9.8.2

PROFINET interface

Interface

SBus interface
(not with function level "Classic")
Transmission technology
Bus termination

Interface to other SBus-capable SEW units
CAN bus to CAN specification 2.0, parts A and B 
ISO 11898-compliant
120 

Ê

 terminating resistor in conjunction with ABOX "MTA...-S02.-...-00" is already 

installed and can be activated via the switch.
With all other ABOX versions, you must use an external terminating resistor.

RS-485 diagnostic interface

Diagnostic interface, not electrically isolated from MOVIFIT

®

 electronics

PROFIBUS

Function level

Classic

Technology

System 

PROFIBUS protocol option

PROFIBUS DP/DPV1

Supported baud rates

9.6 kBaud – 1.5 MBaud / 3-12 MBaud (with automatic detection)

Bus termination

In conjunction with the standard ABOX "MTA...-S02.-...-00", this is already installed and 
can be activated via the switch. With all other ABOX versions, you must use an external 
terminating resistor.

Maximum line length

9.6 kBaud:
19.2 kBaud:
93.75 kBaud:
187.5 kBaud:
500 kBaud:
1.5 MBaud:
12 MBaud:

1,200 m
1,200 m
1,200 m
1,000 m
400 m 
200 m 
100 m
To extend the length, several segments can be coupled using repeaters. The maximum 
expansion/cascading depth can be found in the manuals for the DP master or the repeater 
modules.

Address setting

Addresses 1 to 125 can be set using DIP switches in the connection box.

DP ID number

Classic
600A

hex

 (24586

dec

)

Technology
600B

hex

 (24587

dec

)

System
077A

hex

 (1914

dec

)

GSD file name

Classic

SEW_600A.GSD

Technology

SEW_600B.GSD

System

SEW_077A.GSD

Bitmap file name

Classic

SEW600AN.BMP 

SEW600AS.BMP

Technology

SEW600BN.BMP 

SEW600BS.BMP

-

PROFINET

Function level

Classic

Technology

PROFINET protocol option

PROFINET IO RT

Supported baud rates

100 MBit/s (full duplex)

SEW ID number

010A

hex

Unit ID number

2

Connection technology

M12, RJ45 (push-pull) and RJ45 plug connectors (in the ABOX)

Integrated switch

Supports autocrossing, autonegotiation

Permitted cable types

Category 5 and higher, class D in accordance with IEC 11801

Maximum line length
(from switch to switch)

100 m in accordance with IEEE 802.3

GSD file name

GSDML-V2.1-SEW-MTX-yyyymmdd.xml

GSDML-V2.1-SEW-MTX-yyyymmdd.xml

Bitmap file name

SEW-MTX-Classic.bmp

SEW-MTX-Technology.bmp

P

i

f

kVA

Hz

n

Summary of Contents for MOVIFIT-FC













































































































































































Reviews:

No comments