SEW-Eurodrive MOVIFIT FC Operating Instructions Manual Download Page 10 | Manualshive

Page: 10 / 228

SEW-Eurodrive MOVIFIT FC Operating Instructions Manual Download Page 10

2

Safety notes

Designated use

Operating Instructions – MOVIFIT

®

FC

10

2.4

Designated use

MOVIFIT

®

is a component intended for installation in electrical systems or machines.

In case of installation in machines, startup of MOVIFIT

®

units (i.e. start of designated

operation) is prohibited until it is determined that the machine meets the requirements
stipulated in the Machinery Directive 2006/42/EC.
Startup (i.e. the start of designated use) is only permitted under observance of EMC
Directive 2004/108/EC.
MOVIFIT

®

meets the requirements stipulated in the low voltage directive 2006/95/EC.

The standards contained in the declaration of conformity are used for MOVIFIT

®

.

Adhere to the technical data and information on the connection requirements as provi-
ded on the nameplate and in the documentation.

2.4.1

Safety functions

MOVIFIT

®

may not perform any safety functions unless they are described and ex-

pressly approved.
For safety applications, ensure that the information in the following publications is ob-
served.
• For MOVIFIT

®

with STO (with or without S11 PROFIsafe option):

"MOVIFIT

®

MC/FC – Functional Safety" manual

• For MOVIFIT

®

with S12 safety option:

"MOVIFIT

®

MC/FC – Functional Safety with S12 Safety Option" manual

Use only those components in safety applications that were explicitly designed and
delivered for this purpose by SEW

‑

EURODRIVE. Safety-related components are

marked with the FS logo for functional safety.

2.4.2

Hoist applications

Hoist applications are only permitted with MOVIFIT

®

FC if a hoist startup has been

performed.
Do not use MOVIFIT

®

FC as a safety device in hoist applications. Use monitoring sys-

tems or mechanical protection devices as safety equipment to avoid possible damage
to property or injury to people.

2.5

Transportation, storage

Observe the notes on transportation, storage and proper handling. Observe the climat-
ic conditions as stated in the "Technical Data" sections.

21316996/EN – 12/2014

«
...
8
9
10
11
12
...
»

Summary of Contents for MOVIFIT FC





































































































































































































































Reviews:

No comments