Operating Instructions – MOVI-SWITCH® 1EM
39
9
Technical data of MOVI-SWITCH
®
1EM with binary control
Technical Data
9.2
Technical data of MOVI-SWITCH
®
1EM with binary control
MOVI-SWITCH
®
1EM type
... MSW-1EM-B0 / AVS1
MSW module electronics
MSW-1EM-B0
Part number of MSW
module electronics
1 824 575 7
Line voltages
(depending on the motor)
V
line
AC 3 x 380 V /
400 V
/ 415 V / 460 V / 480 V / 500 V ± 10%
Line frequency
(depending on the motor)
f
line
50 – 60 Hz ± 10%
Rated operating current
AC 1.0 A (at 400 V)
AC 0.75 A (at 500 V)
Position of normal use
Any
Motor protection
TF
Maximum starting
frequency
600 cycles/h
Cycle times
Typical switch-on/switch-off time: 10 ms
Interference immunity
Meets EN 61800-3
Interference emission
Complies with EN 61800-3 and class A limit to EN 55011 and EN 55014
Ambient temperature
ϑ
A
-20 – +40 ˚C (P
N
reduction: 3% I
rated
per K up to max. 60 °C), no moisture condensation
Storage temperature
ϑ
L
-25 – +85 °C (EN 60721-3-3, class 3K3)
Climate class
EN 60721-3-3, class 3K3
Pollution class
2 according to IEC 60664-1 (VDE 0110-1)
Degree of protection
IP54, IP55, IP65 (optional, specify when ordering)
Duty type
S1 (EN 60149-1-1 and 1-3), S3 max. cycle duration 10 minutes
Type of cooling
(DIN 41 751)
Self-cooling
Installation altitude
h
≤
1000 m: no reduction of performance
h > 1000 m: P
rated
reduction by 1% per 100 m
h > 2000 m: V
line
reduction by AC 6 V per 100 m to max. 3 x 400 V at 4000 m asl
h
max
= 4000 m
(see also chapter "Electrical Installation – Installation instructions")
Electronics power supply
(M12 connector AVS1)
Pin 1 (24V)
Pin 3 (0 V)
U = +24 V ± 25%, EN 61131-2, residual ripple max. 13%
I
E
≤
50 mA (without I
OK
)
Binary inputs
Isolated via optocoupler; PLC compatible (EN 61131-2)
R
i
≈
3.0 k
Ω
, I
E
≈
10 mA, sampling cycle
≤
5 ms
Signal level
DC 13 – 30 V = "1" = contact closed
DC
−
3 – +5 V = "0" = contact open
Control functions
(M12 connector AVS1)
Pin 2
RUN/stop
"OK" output
(M12 connector AVS1)
Pin 4
Response time
≤
10 ms
Signaling function
(M12 connector AVS1)
Pin 4
Output for ready signal
Ready for operation checkback signal (high): V
OK
> V
24 V
-3 V
- with voltage present (24 V + supply system)
- in case no error was detected
- at end of self-testing phase (when unit is turned on)
I
OK
Current for checkback max. 0.65 A, short-circuit proof
P
i
f
kVA
Hz
n
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]
