manualshive.com logo in svg

SEW-Eurodrive MOVI-C UHX45A Series, Manual

Share
Download
SEW-Eurodrive MOVI-C UHX45A Series Manual Download Page 46

4

Installation notes

Status LEDs

Manual – MOVI-C

®

 CONTROLLER advanced with PROFINET IO Fieldbus Interface

46

4.5.8

Status LED "BF" (BUS FAULT)

Indicates  a  bus  error.  The  status  LED  "BF"  meets  and  expands  the  requirements  of
AIDA (

A

utomation 

I

nitiative of German 

D

omestic 

A

utomobile manufacturers).

Status

Possible cause

Measure

Off

There is a controlling connec-
tion to the fieldbus master
(PLC).

–

Orange

The fieldbus slave (device)
does not support the con-
figured functions in the field-
bus master.

Perform the configuration
again.

Red

•

No connection could be
established to the fieldbus
master.

•

The connection to the
fieldbus master has been
interrupted.

Check the PROFINET device
name in the fieldbus master
and fieldbus slave.

4.5.9

Status LEDs "L/A" (Link/Activity)

Indicate the status of the Ethernet connection.

Status LED

Meaning

Green

There is an Ethernet connection.

EtherCAT

®

/SBus

PLUS

 interface:

Green, flashing

Data is currently being exchanged via Ether-
net.

Engineering interface and fieldbus
interface: Orange, flashing

Data is currently being exchanged via Ether-
net.

Off

There is no Ethernet connection.

24777730/EN – 01/2018

Summary of Contents for MOVI-C UHX45A Series





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands