SEW-Eurodrive MOVI-C UHX25A Series Manual Download Page 23

Page: 23 / 72

Installation notes

Electrical installation

Manual – MOVI‑C

CONTROLLER standard UHX25A

4.2.5

EtherCAT

®/

SBus

PLUS

master connection

The MOVI-C

CONTROLLER serves as EtherCAT

/SBus

PLUS

master for the lower-

level application inverters (EtherCAT

/SBus

PLUS

slaves). The communication takes

place via the EtherCAT

-based, fast system bus SBus

PLUS

(X30).

EtherCAT

/SBus

PLUS

bus topology

EtherCAT

/SBus

PLUS

is designed for linear bus structure with RJ45 connectors. The

EtherCAT

/SBus

PLUS

slave devices are connected via a shielded twisted-pair cable.

[3]

[4]

[1]

[2]

9007219818005771

[1] System bus cable, 4-pin, color: light gray

The cable is

not

included in the delivery

[2] Module bus cable, 8-pin, color: anthracite gray
[3] MOVIDRIVE

modular

[4] MOVI-C

CONTROLLER

INFORMATION

According to IEEE 802.3, 200 Edition, the maximum cable length for
10 MBaud/100 MBaud Ethernet (10BaseT/100BaseT) between 2 EtherCAT

SBus

PLUS

stations is 100 m.

Bus termination

Bus termination (for example with bus terminating resistors) is not necessary. The sys-
tem detects automatically if there is no subsequent device connected to a device.

25800736/EN – 08/2018

Summary of Contents for MOVI-C UHX25A Series









































































Search results

Summary of Contents for MOVI-C UHX25A Series

Reviews:

SEW-Eurodrive MOVI-C UHX25A Series, Manual, Page: 23 / 72

Search results

Summary of Contents for MOVI-C UHX25A Series

Reviews: