SEW-Eurodrive MFC1/FHX Series Operating Instructions Manual Download Page 48

Page: 48 / 164

Electrical installation

Communication interfaces

Operating Instructions – MOVI-C

FIELD CONTROLLER standard/advanced

5.7

Communication interfaces

5.7.1

CAN system bus

The communication interface is available for project-specific use. Before using the

communication interface, contact

SEW‑EURODRIVE

Service.

MOVILINK

, CANopen and the control of

generation

B inverters cannot be implemen-

ted via the communication interface.

5.7.2

RS485 interface

The communication interface is available for project-specific use. Before using the

communication interface, contact

SEW‑EURODRIVE

Service.

5.8

Cable routing and cable shielding

5.8.1

Installation with separately routed Ethernet cable

Notes on cable routing and shielding – Recommended cable routing

Note the following when routing and shielding the cables:
• Cable selection

– For cable selection, note the chapter "Technical data and dimension sheets/

specification of recommended Ethernet connection cable" in the operating in-

structions.

– You can use unshielded connection cables for the supply system connection.

• Cable shielding

– Connect the cable shields to the optionally available EMC cable glands, see

chapter "Cable glands".

• Observe the permitted bending radii of the installed cables for cable routing.

26872137/EN – 12/2021

Summary of Contents for MFC1/FHX Series





































































































































































Search results

Summary of Contents for MFC1/FHX Series

Reviews:

SEW-Eurodrive MFC1/FHX Series, Operating Instructions Manual, Page: 48 / 164

Search results

Summary of Contents for MFC1/FHX Series

Reviews: