SEW-Eurodrive MFC1/FHX Series Operating Instructions Manual Download Page 44

Page: 44 / 164

Electrical installation

Installation topology (installation with PAC hybrid cable)

Operating Instructions – MOVI-C

FIELD CONTROLLER standard/advanced

5.4

Installation topology (installation with PAC hybrid cable)

The following figure shows a basic installation topology with the device:

Control

Supply system

24 V

Back-up

fuse/line

protection

Control cabinet level

Field level

MOVI-C® FIELD CONTROLLER MFC1../FHX

[4] MOVIGEAR® performance

[4] MOVIMOT® performance

[4] MOVIMOT® advanced

[4] MOVIMOT® flexible

[4] MOVIGEAR® classic

[1]

Fieldbus

[3]

[2]

[5]

27021626478764555

[1]

The maximum permitted cable length between the controller (PLC) and the

MOVI-C

FIELD CONTROLLER

is 100 m. The cable length may be reduced due to the technical data

of the controller (PLC).

[2]

The MOVI-C

FIELD CONTROLLER

is not equipped with an integrated DC 24 V supply. The electron-

ics must be supplied externally with DC 24 V.

[3]

Decentralized motion and logic controller

[4]

MOVI-C

decentralized drive technology

[5]

PAC hybrid cable for 400 V power supply, DC 24 V supply, and EtherCAT

/SBus

PLUS

communication

26872137/EN – 12/2021

Summary of Contents for MFC1/FHX Series





































































































































































Search results

Summary of Contents for MFC1/FHX Series

Reviews:

SEW-Eurodrive MFC1/FHX Series, Operating Instructions Manual, Page: 44 / 164

Search results

Summary of Contents for MFC1/FHX Series

Reviews: