SEW-Eurodrive MFC1/FHX Series Operating Instructions Manual Download Page 151

Page: 151 / 164

Technical data and dimension sheets

Dimension drawings of plug connectors in the connection box

Operating Instructions – MOVI-C

FIELD CONTROLLER standard/advanced

151

10.9

Dimension drawings of plug connectors in the connection box

10.9.1

MFC1.. design

Plug connector

INFORMATION

• The following figure shows an example of the additional dimensions of the op-

tional plug connectors for a possible plug connector configuration.

• For more information, refer to chapter "Plug connector positions".

[3]

[1]

[2]

[4]

28692454795

[1]

Optional pressure compensation

[2]

M23 plug connector design, female

[3]

M12 plug connector design, female

[4]

M12 plug connector design, male

26872137/EN – 12/2021

Summary of Contents for MFC1/FHX Series





































































































































































Search results

Summary of Contents for MFC1/FHX Series

Reviews:

SEW-Eurodrive MFC1/FHX Series, Operating Instructions Manual, Page: 151 / 164

Search results

Summary of Contents for MFC1/FHX Series

Reviews: