SEW-Eurodrive MFC1/FHX Series Operating Instructions Manual Download Page 122

Page: 122 / 164

Service

Device replacement in MOVISUITE®

Operating Instructions – MOVI-C

FIELD CONTROLLER standard/advanced

122

3. Under "Configuration data", enable the "Controller replacement function".
4. Click on the [Update configuration data] button.

The current failsafe data of the

MOVI‑C

FIELD CONTROLLER is stored once

on the OMH memory card. All of the data that is required when replacing the

MOVI‑C

FIELD CONTROLLER is in this way stored on the OMH memory card

so that the system can run again in the same way as before the replacement. A

detailed list of the stored data can be found in the table below. This information

may vary depending on the firmware version.

INFORMATION

The PROFINET device name is not saved and restored. To save the PROFINET

device name, assign the name via the control software of the PLC or perform a topol-

ogy-based naming so that the PLC project assigns the name automatically.

NV data

Category

IP settings

Backup and restore

IEC settings

Backup and restore

Customer-specific device designation

Backup and restore

Fieldbus parameters

Backup and restore

Time/date settings

Backup and restore

Device faults and info

Backup only, no restore

Device faults and info

Backup only, no restore

IEC RETAIN/PERSISTENT

Not backed up. To back up this data, con-

tact

SEW‑EURODRIVE

Service.

5. Insert the OMH memory card of the

MOVI‑C

FIELD CONTROLLER to be re-

placed

into

the

corresponding

card

slot

the

new

MOVI‑C

FIELD CONTROLLER

The most recently saved failsafe data is transferred from the OMH memory

card to the

MOVI‑C

FIELD CONTROLLER

8.6.2

Firmware update

INFORMATION

The firmware update is shown below taking the example of a control cabinet control-

ler.

Perform the steps described in the following chapters to update the firmware of the

MOVI-C

FIELD CONTROLLER.

Exporting a firmware image

1. Create a new project in MOVISUITE

via "Planning" in the "Start" menu.

2. In the function view of the MOVISUITE

project, add the required

MOVI-C

CONTROLLER in the required version.

3. Select the MOVI-C

CONTROLLER in the MOVISUITE

project.

The configuration menu of the

MOVI‑C

CONTROLLER opens.

26872137/EN – 12/2021

Summary of Contents for MFC1/FHX Series





































































































































































Search results

Summary of Contents for MFC1/FHX Series

Reviews:

SEW-Eurodrive MFC1/FHX Series, Operating Instructions Manual, Page: 122 / 164

Search results

Summary of Contents for MFC1/FHX Series

Reviews: