SEW-Eurodrive DR63 Series Addendum To The Operation Instructions Download Page 57

Page: 57 / 64

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280

AC motors DR.63 in category 3GD

Declarations of Conformity

11.2 AC motors DR.63 in category 3GD

4112853387

EC Declaration of Conformity

Bruchsal

Johann Soder

Place

Date

Managing Director Technology

a) b)

a) Authorized representative for issuing this declaration on behalf of the manufacturer
b) Authorized representative for compiling the technical documents

901160011

11.07.11

SEW-EURODRIVE GmbH & Co KG

Ernst-Blickle-Straße 42, D-76646 Bruchsal

declares under sole responsibility that the

motors of the series

DR63

category

3GD

labeling

II3G Ex nA IIB T3 Gc
II3G Ex nA IIC T3 Gc
II3D Ex tc IIIB T120°C Dc
II3D Ex tc IIIB T140°C Dc
II3D Ex tc IIIC T120°C Dc
II3D Ex tc IIIC T140°C Dc

are in conformity with

ATEX Directive

1994/9/EC

Applied harmonized standards

EN 60034-1:2004
EN 60079-0:2009
EN 60079-15:2010
EN 60079-31:2010

Summary of Contents for DR63 Series

































































Search results

Summary of Contents for DR63 Series

Reviews:

SEW-Eurodrive DR63 Series, Addendum To The Operation Instructions, Page: 57 / 64

Search results

Summary of Contents for DR63 Series

Reviews: