manualshive.com logo in svg

SEW-Eurodrive DR63 Series, Addendum To The Operation Instructions, Page: 38 / 64

Share
Download
SEW-Eurodrive DR63 Series Addendum To The Operation Instructions Download Page 38

38

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280

6

Use

Duty Types and Limit Values

6.2

Use

6.2.1

Motors of category 2G and 2GD

The necessary information for this is listed on the nameplate.

NOTES ON EXPLOSION PROTECTION

• It is not permitted to connect more than one motor to one frequency inverter.

• The voltage at the motor terminal board must projected be to prevent overheating.

 

• If the motor voltage is too low (undercompensation), slip increases, which causes

higher temperatures in the rotor of the motor. 

• If the mechanical load is the same, operation on a frequency inverter causes a

more significant motor temperature rise due to the harmonic content in current and

voltage.

NOTES ON EXPLOSION PROTECTION

• The frequency inverter can only be operated with motors that are permitted for this

operating mode according to the EC prototype test certificate.

• Verification that the motor voltage matches the specifications of the EC prototype

test certificate must be provided during startup.

P

i

f

kVA

Hz

n

Summary of Contents for DR63 Series

































































Reviews:

No comments