manualshive.com logo in svg

SEW-Eurodrive DR63 Series, Addendum To The Operation Instructions, Page: 28 / 64

Share
Download
SEW-Eurodrive DR63 Series Addendum To The Operation Instructions Download Page 28

28

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280

5

Connecting category 3G and 3GD motors

Electrical Installation

5.12.1 Motor connection

Cage clamp

With motors of size 63, the supply cables must be secured in the spring clamp terminal
strip according to the wiring diagram. Connect the protective earth to the protective con-
ductor connection so that the cable lug and housing material are separated by a washer:

5.13 Connecting category 3G and 3GD motors

You can obtain the following wiring diagrams from SEW-EURODRIVE by specifying the
order number of the motor (see chapter "Nameplate" in the corresponding detailed op-
erating instructions):

5.13.1 Motor connection

The motors are supplied and connected differently depending on the size and electrical
design. Comply with the connection type specified in the following table. 

Observe the permitted air and creeping distances when connecting the supply system
cable.

 connection

 connection 

PE connection

TF TF

3

2

1

4

TF TF

3

2

1

4

Series

Number of poles

Connection

Associated wiring diagram

(designation/number)

X = Placeholder for the version

DR63

4, 6

 / 

DT14 / 08 857 X 03

DVE250/280

4

 / 

DT13 / 08 798 X 06

Series

Connection

DR63

Motor connection via cage clamp

DVE250/280

Motor connection via terminal board

Summary of Contents for DR63 Series

































































Reviews:

No comments