manualshive.com logo in svg

SEW-Eurodrive DR63 Series, Addendum To The Operation Instructions, Page: 27 / 64

Share
Download
SEW-Eurodrive DR63 Series Addendum To The Operation Instructions Download Page 27

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280 

27

5

Notes regarding the connection of the motor

Electrical Installation

5.11 Notes regarding the connection of the motor

Observe the following points when you connect the motor:

• Check cable cross section

• Arrange terminal links correctly

• Screw on the connections and the PE conductor correctly

• Make sure that the connection cables are not cramped in to avoid damage to the in-

sulation. 

• Observe clearances

• In the terminal box: Check winding connections and tighten them if necessary

• Perform the connection in accordance with the enclosed wiring diagram

• Avoid protruding wire ends

• Observe the specified direction of rotation

5.12 Connecting category 2G and 2GD motors

You can obtain the following wiring diagrams from SEW-EURODRIVE by specifying the
order number of the motor (see chapter "Nameplate" in the corresponding detailed op-
erating instructions):

INFORMATION

It is essential to comply with the valid wiring diagram. Do not connect or start up the
motor if this wiring diagram is missing. The relevant wiring diagrams are available from
SEW-EURODRIVE free of charge.

INFORMATION

The terminal box must be free from foreign objects, dirt and humidity. Unused cable
entry openings and the terminal box itself must be closed so they are dust and water-
proof.

Series

Number of poles

Associated wiring diagram

(designation/number)

X = Placeholder for the version

eDR63

4

DT14 / 08 857 X 03

Summary of Contents for DR63 Series

































































Reviews:

No comments