manualshive.com logo in svg

SEW-Eurodrive DR63 Series, Addendum To The Operation Instructions, Page: 25 / 64

Share
Download
SEW-Eurodrive DR63 Series Addendum To The Operation Instructions Download Page 25

Operating Instructions – Explosion-Proof AC Motors DR63/eDR63, DVE250/280 

25

5

Special aspects for operation with frequency inverter

Electrical Installation

5.7

Special aspects for operation with frequency inverter

When motors are powered from inverters, you must observe the wiring instructions is-
sued by the inverter manufacturer. It is essential that you observe chapter "Operating
modes and limit values" as well as the operating instructions of the frequency inverter.

5.8

Improving the grounding (EMC)

For improved low-impedance grounding at high frequencies, we recommend using the
following connections with DR/DV(E) AC motors:

• DVE250 and 280: M16 screw and 2 serrated lock washers in the bore of the eyebolt

5.9

Special aspects in switching operation

When the motors are used in switching operation, possible interference of the switch-
gear must be excluded by ensuring suitable wiring. According to IEC 60204 (electrical
equipment of machines), motor windings must have interference suppression to protect
the numerical or programmable logic controllers. As it is primarily switching operations
that cause interference, SEW-EURODRIVE recommends installing protective circuitry
in the switching devices.

[1]

Summary of Contents for DR63 Series

































































Reviews:

No comments