SEW-Eurodrive CMP40 Operating Instructions Manual Download | Manualshive

Page: 30 / 88

background image

30

Operating Instructions – Explosion-Proof CMP Synchronous Servomotors

5

Wiring information

Electrical Installation

The right-angle connectors can be rotated to achieve the required position.

Different positions of the adjustable connectors

5.8

Wiring information

5.8.1

Protecting the brake control system against interference

To protect the brake control system against interference, do not route unshielded brake
cables together with switched-mode power cables.
Switched-mode power cables include in particular:
• Output cables from inverters, converters, soft start units and brake units
• Supply cables to braking resistors and similar.

5.8.2

Thermal motor protection

5.8.3

Special aspects for operation with a servo inverter

When servomotors are powered from inverters, the wiring instructions issued by the in-
verter manufacturer must be followed. Observe section "Operation" on page 37 And the
operating instructions for the inverter.

NOTE

The connector should only be rotated to install and connect the servomotor. Do

not

expose

the connector to permanent motion once it has been installed.

63406AXX

STOP!

Install the connecting lead of the KTY separately from other power cables, maintaining
a distance of at least 200 mm. The cables can only be routed together if either the KTY
cable or the power cable is shielded.

«
...
28
29
30
31
32
...
»

Summary of Contents for CMP40

























































































Reviews:

No comments

Related manuals for CMP40

Xcelorin LOSB9400 3.5T

Brand: Team Losi Pages: 4

Brand: Scania Pages: 55

Brand: Himax Pages: 2

Brand: ACME motori Pages: 23

Brand: Texas Equipment Pages: 38

Brand: Stober Pages: 34

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: Volvo Penta Pages: 112

Brand: Honda Pages: 96

Brand: Honda Pages: 114

Car Engine GX340

Brand: Honda Pages: 96

ARO AF1060 Series

Brand: Ingersoll-Rand Pages: 8

Brand: Ingersoll-Rand Pages: 8

Brand: Ingersoll-Rand Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands