SEW-Eurodrive CMP40 Operating Instructions Manual Download Page 24

Page: 24 / 88

Operating Instructions – Explosion-Proof CMP Synchronous Servomotors

Connecting the CMP servomotor

Electrical Installation

5.4

Connecting the CMP servomotor

5.4.1

Procedure

• Connect the servomotor according to the enclosed wiring diagram.
• Check whether the cable cross sections comply with:

• The rated motor current
• The applicable installation instructions
• The requirements of the place of installation

• Screw on the connections and PE conductors.
• Check the winding connections in the terminal box and tighten them, if necessary.

5.4.2

Wiring diagrams

The following applies to all wiring diagrams:
• View on wiring side
• Colors according to SEW-EURODRIVE cable:

NOTE

The servomotor must only ever be connected as shown in the following wiring diagram,
which is also included with the servomotor.

Color code

Color

Black

Brown

Blue

Green

Gray

Orange

Pink

Red

Violet

White

Yellow

GY / PK

Gray/pink

RD / BU

Red/blue

BK / WH

Black/white

RD / WH

Red/white

Summary of Contents for CMP40

























































































Search results

Summary of Contents for CMP40

Reviews:

SEW-Eurodrive CMP40, Operating Instructions Manual, Page: 24 / 88

Search results

Summary of Contents for CMP40

Reviews: