background image

CAUTION

CARE MUST BE TAKEN NOT TO TOUCH THE PRESSURE SENSITIVE
DIAPHRAGM WHILE CLEANING THE PRESSURE PORT.  FAILURE TO
OBSERVE THIS PRECAUTION CAN CAUSE IRREPARABLE DAMAGE

.

WARRANTY

The Company warrants its products to be free from defects in material and workmanship in normal use
and service for a period of two years from date of shipment.  The Company reserves the right and
option to refund the purchase price in lieu of repair or replacement upon evaluation of the returned
original part.  Modification, misuse, attempted repair by others, improper installation or operation shall
render this guarantee null and void.  The Company makes no warranty of merchantability or fitness for a
part or purpose.

SERVICING

The transducer cannot be repaired locally and if damaged should be returned to Setra Systems with the
following:-

1.

 

Name and phone number of person to contact

2.

 

Shipping and billing information

3.

 

Full description of malfunction

4.

 

Remove any pressure fitting and plumbing that you may have installed and enclose any required
mating electrical connectors and wiring diagrams.

Please ship to Setra Systems at the address shown below or to your local Setra Distributor when a
replacement/repair is required.

United States

Outside The United States

Setra Systems Inc

Contact your local Setra Distributor

159 Swanson Road
Boxborough, MA 01719
Attn: Repair Department

RETURN TO FACTORY

PLEASE NOTE

:  To comply with Health and Safety requirements, the instrument must be clean and

safe to handle and accompanied by a formal statement to that effect duly signed by an authorised officer
of the Company.

Any instrument returned without certification will be quarantined and no action will occur until cleared.  It
may ultimately be returned to you and subject to a transportation charge.

Summary of Contents for 540 Series










Reviews: