Server Technology Switched Rack PDU Installation And Operation Manual Download Page 95 | Manualshive

Page: 95 / 157

background image

Switched PDU
Installation and Operations Manual

Operations



95

Displaying UPS configuration:

The Show UPS command displays information about all UPS devices.



UPS Type and Host/IP address



UPS SNMP port and community string



SNMP Objects OID values and expected return values

To display UPS configuration information:

At the Switched CDU: prompt, type

show ups

and press

Enter

.

Example

The following command displays UPS configuration information:

Switched CDU: show ups<Enter>
1 Type: Liebert
Host/IP: DC1Liebert1
Voltage Polling: ON
SNMP Configuration
  Community String: public
      SNMP Port: 162
  SNMP Objects/Expected Values
Voltage: .1.3.6.1.2.1.33.1.4.4.1.2.1
Utility Status: .1.3.6.1.2.1.33.1.4.1.0
  On Battery: 0x5
  On Utility: 0x3
   More (Y/es N/o):

Feature Administration

Displaying activated special features:

The Show Features command displays all activated special features for the device.

To display activated special features:

At the Switched CDU: prompt, type

show features

and press

Enter

.

Example

The following command displays all activated special features:

Switched CDU: show features<Enter>
Activated Features:
Smart Load Shedding

NOTE:

A restart of the PDU is required after activating new special features.

«
...
93
94
95
96
97
...
»

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments

Related manuals for Switched Rack PDU

Brand: DayTronic Pages: 16

Brand: ESAB Pages: 28

Brand: DEFA Pages: 8

Brand: ABB Pages: 2

Brand: P.Lindberg Pages: 38

Powermax Series PM8-EX

Brand: Panamax Pages: 2

Dual-Circuit Power Distribution Unit

Brand: Black Box Pages: 1

Brand: D-fend Pages: 28

Brand: Videotec Pages: 56

Brand: Denali Pages: 2

Brand: DIODE LED Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands