Server Technology Switched Rack PDU Installation And Operation Manual Download Page 87 | Manualshive

Page: 87 / 157

background image

Switched PDU
Installation and Operations Manual

Operations



87

Telnet Administration

NOTE:

A restart of the PDU is required after setting or changing

any

Telnet/Web configurations.

Enabling and disabling Telnet support:

The Set Telnet command is used to enable or disable Telnet support.

To enable or disable Telnet support:

At the Switched CDU: prompt, type

set telnet

, followed by

enabled

or

disabled

and press

Enter

.

Changing the Telnet port:

With Telnet support enabled, the Telnet server watches and responds to requests on the default Telnet port number 23. You
can change this port number using the Set Telnet Port command.

To change the Telnet socket:

At the Switched CDU: prompt, type

set telnet port

, followed by the port number and press

Enter

.

Example

The following changes the Telnet port number to 7001:

Switched CDU: set telnet port 7001<Enter>

FTP Administration

You can upload new versions of firmware into the PDU using File Transfer Protocol (FTP). This allows access to
new firmware releases for firmware improvements and new features additions. The following commands are used to
configure the PDU for an FTP firmware upload. For more information about initiating an FTP firmware upload, see
Appendix B.

NOTE:

Secure File Transport Protocol (SFTP) is also supported for encrypted SSH transport over the network.

Setting the FTP host address:

The Set FTP Host command sets the FTP host IP address or hostname allowing for firmware file uploads.

To set the FTP Host address:

At the Switched CDU: prompt, type

set ftp host

, followed by the IP address or hostname and press

Enter

.

NOTE:

Both IPv4 and IPv6 formats are accepted for IP address or hostname.

Examples

The following command sets the FTP host IP address to 12.34.56.99:

Switched CDU: set ftp host 12.34.56.99<Enter>

The following command sets the FTP hostname to ftp.servertech.com:

Switched CDU: set ftp host ftp.servertech.com<Enter>

Setting the FTP username:

The Set FTP Username command sets the username as required by the FTP Host.

To set the FTP username:

At the Switched CDU: prompt, type

set ftp username

, followed by the FTP username and press

Enter

.

Example

The following command sets the FTP username to Guest:

Switched CDU: set ftp username guest<Enter>

«
...
85
86
87
88
89
...
»

Summary of Contents for Switched Rack PDU






























































































































































Reviews:

No comments

Related manuals for Switched Rack PDU

Brand: H&H Pages: 33

Brand: PDi Pages: 107

Brand: Furman Pages: 28

Brand: Rotel Pages: 7

Brand: T+A Elektroakustik Pages: 16

Brand: CHIEF Pages: 12

VR 5000 noSpool

Brand: Fronius Pages: 132

Brand: Atlas Pages: 12

Brand: ABB Pages: 33

NXA-PDU-1508-08

Brand: AMX Pages: 20

VideoEase 500150

Brand: MuxLab Pages: 16

Brand: Bals Pages: 20

Brand: Tripp Lite Pages: 4

Brand: Stanley Pages: 12

RA5014-515-15A-515

Brand: Synergy Global Technology Pages: 5

RA5024-520-20A-L520

Brand: Synergy Global Technology Pages: 7

InfraPower IPM-01

Brand: Synergy Global Technology Pages: 36

Brand: Keysight Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands