background image

SHANGHAI SERMATEC ENERGY TECHNOLOGY CO.,LTD

- 22 -

Attention

Do not install the equipment in the place that will affect the working

and living environment, because the normal operation of the

equipment will produce sound.

4.6 Installation method and space

The installation space of the energy storage cabinet shall ensure a

proper distance from the surrounding wall, so as to ensure that the

machine is convenient for opening and closing doors, plugging and

unplugging modules, normal heat dissipation and enough space for

the user to operate.

4.6.1 Installation space

The front and back sides of the energy storage cabinet shall not be

close to the wall. In order to ensure the normal operation of the

energy storage cabinet, the front and back sides of the energy storage

cabinet shall be kept at a reasonable distance. The distance between

the front cabinet door and the obstacles shall be kept above 1500mm

to ensure the necessary maintenance space, so that the cabinet can

open the door for maintenance and remove the battery module. The

distance between the front of the back cabinet door and the obstacles

shall be kept at least 1000mm, which not only ensures the necessary

maintenance door, but also ensures the cooling space of the back air

conditioner (as shown in Figure 4-2)

Fi

gure 4-2 Installation space of

energy storage device

Summary of Contents for SMT-100kWh



































































Reviews: