SEPTENTRIO PolaRx5TR Reference Manual Download Page 135 | Manualshive

Page: 135 / 512

background image

3 Command Line Reference

epss

gpss

exePPPSetSeedGeod

getPPPSetSeedGeod

Latitude

Longitude

Altitude

Datum

-90.000000000
. . . 0.000000000
. . . 90.000000000
deg

-180.000000000
. . . 0.000000000
. . . 180.000000000
deg

-1000.0000
. . . 0.0000
. . . 30000.0000 m

WGS84

ETRS89

NAD83

NAD83_PA

NAD83_MA

GDA94

GDA2020

User1

User2

Other

RxControl: Navigation > Receiver Initialization > PPP Set Seed

Use this command to seed the PPP engine with the speciﬁed position. The geodetic coordi-
nates in the

Latitude

,

Longitude

and

Altitude

arguments are that of the marker, and not of the

ARP. The argument

Longitude

is positive to the east of Greenwich.

The datum to which the coordinates refer must be speciﬁed with the

Datum

argument:

Datum

Description

WGS84

WGS84 or ITRFxx (the receiver does not make a distinction be-
tween them)

ETRS89

European ETRS89 (ETRF2000 realization)

NAD83

NAD83(2011), North American Datum (2011)

NAD83_PA

NAD83(PA11), North American Datum, Paciﬁc plate (2011)

NAD83_MA

NAD83(MA11), North American Datum, Marianas plate (2011)

GDA94

GDA94(2010), Geocentric Datum of Australia (2010)

GDA2020

GDA2020, Geocentric Datum of Australia 2020

User1

First user-deﬁned datum. The corresponding transformation
parameters must be speciﬁed by the

setUserDatum

and

setUserDatumVel

commands, while the corresponding ellip-

soid must be deﬁned by the

setUserEllipsoid

command.

User2

Second user-deﬁned datum

Other

Datum not in the list or unknown

The receiver applies the necessary transformations to ITRF (the datum used by the PPP en-
gine) automatically. If the

Datum

argument is set to

Other

, no datum transformation is ap-

plied.

It is the user’s responsibility to ensure that the speciﬁed marker position is centimeter-
accurate and that the datum is properly speciﬁed. Inaccurate seeding will result in a long
convergence time, and/or in an incorrect estimate of the variance/covariance matrix of the
PPP solution.

At the moment when the command is entered, the receiver must be static. To prevent gross
errors, the command is ignored when the seed signiﬁcantly differs from the current position
computed by the receiver, or when the current velocity is not zero.

135

«
...
133
134
135
136
137
...
»

Summary of Contents for PolaRx5TR

































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PolaRx5TR

Brand: Farallon Pages: 26

Brand: Observint Pages: 11

ThunderLAN TNETE100A

Brand: Texas Instruments Pages: 179

PARTNER Voice Messaging PC Card Release 2

Brand: Lucent Technologies Pages: 67

Brand: Lanner Pages: 63

Brand: XNET Pages: 17

Brand: EMCIS Pages: 14

Brand: XtendLan Pages: 228

Brand: ADTRAN Pages: 20

Brand: ETAS Pages: 36

MP5S Plus Writer

Brand: SONIX Pages: 23

Brand: EVGA Pages: 3

Brand: Kordis Pages: 31

Brand: Westermo Pages: 22

Brand: TRENDnet Pages: 15

Brand: Abocom Pages: 59

Brand: HYCON Pages: 13

X-NUCLEO-AMICAM1

Brand: ST Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands