SenTech STC-MBS322U3V Product Specifications Download Page 41

Page: 41 / 65

No.15S103-01

41/65

STC-MBS510U3V / STC-MCS510U3V / STC-MBS322U3V / STC-MCS322U3V

Specifications and Use

’s guide

When utilizing the Multi-ROI function, please make note of the following:

This image format is Sentech original format, it does not comply with USB3Vision. Therefore this Multi ROI will
not work on 3

party applications that conform to USB3Vision.

To use Multi ROI, one of following application is required.

・

The application that built on Sentech’s SDK

・

The application that built on Sentech’s DirectShowFilter

・

The application that built on Sentech’s GenTL module (*1)
(*1) Sent

ech’s original format data process has to be implemented into application

Multi ROI can be configure 16 regions as Region 0 to 15.

Restriction of ROI operation

・

Region 0 is always ON

・

Region(X+Y) can be enable (ON) after sets ON Region(X) and Region(Y).

(X, Y : Region number, X is any number from 1 to 3, Y is any number from 4,8,12)

・

The following restriction exist to set region’s Width, Height, OffsetX and OffsetY

Width[RegionN] = Width[Region(N+4)] = Width[Region(N+8)] = Width[Region(N+12)]

Region12

Region13

Region14

Region3

Region7

Region11

Region15

Region8

Region9

Region10

Region0

Region1

Region2

Region4

Region5

Region6

OffsetX
[Region0]

OffsetY
[Region0]

WidthMax

OffsetY
[Region4]

OffsetY
[Region8]

OffsetX
[Region1]

OffsetX
[Region2]

Width[Region0]

eigh
t[R

egi

on
0

]

eigh
tM

OffsetX
[Region3]

OffsetY
[Region12]

Width[Region1]

Width[Region2]

Width[Region3]

eigh
t[R

egi

on
1

]

eigh
t[R

egi

on
8

]

eigh
t[R

egi

]

Summary of Contents for STC-MBS322U3V


































































Search results

Summary of Contents for STC-MBS322U3V

Reviews:

Related manuals for STC-MBS322U3V

Brands by name

Popular brands

SenTech STC-MBS322U3V, Product Specifications

Search results

Summary of Contents for STC-MBS322U3V

Reviews:

Related manuals for STC-MBS322U3V

Brands by name

Popular brands